直井地面驱动螺杆泵采油杆管偏磨机理

doi:10.7623/syxb201202019

石油学报 ›› 2012, Vol. 33 ›› Issue (2): 304-309.DOI: 10.7623/syxb201202019

直井地面驱动螺杆泵采油杆管偏磨机理

董世民　张万胜　王　强　柴国鸿　苏艳玲

燕山大学机械工程学院　河北秦皇岛　066004

收稿日期:2011-09-03 修回日期:2011-12-18 出版日期:2012-03-25 发布日期:2012-05-17
通讯作者: 董世民
作者简介:董世民，男，1962年9月生，1998年获西南石油学院博士学位，现为燕山大学机械工程学院教授、博士生导师，主要从事机械采油系统动态仿真与运行优化的科研工作。
基金资助:
国家自然科学基金项目（No.50974108）资助。

Mechanism of eccentric wear between rod string and tubing string of a surface driving screw pump lifting system in vertical wells

DONG Shimin　ZHANG Wansheng　WANG Qiang　CHAI Guohong　SU Yanling

Received:2011-09-03 Revised:2011-12-18 Online:2012-03-25 Published:2012-05-17

摘要/Abstract

摘要：

将直井地面驱动螺杆泵采油杆柱简化为在油管内偏心旋转的杆柱。考虑了杆柱偏心旋转惯性离心力、轴向力对杆柱横向弯曲变形的影响。应用可移动双向弹簧元模拟杆管接触状态，并考虑了杆体、结箍以及扶正器与油管间隙不同对杆柱挠度约束的差别，建立了螺杆泵采油杆柱在油管内受力变形的有限元仿真模型。仿真结果表明：抽油杆柱在油管内偏心旋转会产生陀螺效应，杆柱在油管内变形形态呈下密上疏的螺旋状,这是直井地面驱动螺杆泵采油系统杆管偏磨的主要原因之一。杆柱与油管接触段长度主要取决于转速、下泵深度和偏心距等参数。当转速较高时，几乎所有接箍均与油管内壁接触，也会出现杆体与油管内壁接触的现象。

关键词: 地面驱动螺杆泵, 抽油杆柱, 偏心旋转, 陀螺效应, 偏磨机理, 仿真模型

Abstract:

The rod string of a surface driving screw pump system in vertical wells can be simplified as an eccentric rotation rod string in the tubing string. In this case, effects of the axial force and inertial centrifugal force caused by eccentric rotation of a rod string on the lateral bending deformation of the rod string must be investigated. We employed removable biaxial spring elements to describe the contacting state between the rod string and tubing string, and a finite element simulation model for describing the deformation of a screw pump rod string in the tubing string was set up on condition that all the differences caused by different interspace between the rod body, coupling, centralizer and the tubing string in constraints on the bending deflection of a rod string have been taken into consideration. Simulation results demonstrate that the eccentric rotation of a rod string in the tubing string can produce a gyro effect that may lead to a lateral deformation of the rod string, and the deformed rod string is commonly in a helical shape with helixes decreasing upward, which is one of the major reasons to generate the eccentric wear between the rod string and tubing string of a surface driving screw pump system in vertical wells. The contacting length between the rod string and tubing string mainly depends on some operating parameters, such as rotation speed, puttingon depth of the pump, eccentricity, etc. With a higher rotation speed, almost all the couplings on the rod string will contact with internal walls of the tubing string, and the rod body may also touch internal walls of the tubing string occasionally.

Key words: surface driving screw pump；rod string；eccentric rotation；gyro effect, eccentric wear mechanism, simulation model

董世民　张万胜　王　强　柴国鸿　苏艳玲. 直井地面驱动螺杆泵采油杆管偏磨机理[J]. 石油学报, 2012, 33(2): 304-309.

DONG Shimin　ZHANG Wansheng　WANG Qiang　CHAI Guohong　SU Yanling. Mechanism of eccentric wear between rod string and tubing string of a surface driving screw pump lifting system in vertical wells[J]. Editorial office of ACTA PETROLEI SINICA, 2012, 33(2): 304-309.

参考文献

[1]陈实,王海文,赵伟,等.螺杆泵井偏磨机理的研究[J].断块油气田,2007,14(1):80-82．

Chen Shi,Wang Haiwen,Zhao Wei,et al.Mechanism study on eccentric wear of rod in production well by adopting progressive cavity pump[J].Fault-block Oil & Gas Field,2007,14(1):80-82．

[2]祝庆远，王民轩，罗俊，等.螺杆泵采油油管柱弯曲对抽油杆柱的影响[J]．石油机械，1999，27(10):38-39.

Zhu Qingyuan,Wang Minxuan,Luo Jun,et al.Effect of tubing string bending on rod string[J].China Petroleum Machinery,1999,27(10):38-39.

[3]张佳民.螺杆泵抽油杆柱设计方法及其应用[M].北京:石油工业出版社,2002:17-27.

Zhang Jiamin.Design method of screw pump sucker rod string and its application[M].Beijing:Petroleum Industry Press,2002:17-27.

[4]程鹏，顾雪林，胡才志，等．地面驱动单螺杆泵抽油杆失效分析与预防措施[J]．石油机械，2000，28(4):26-27．

Cheng Peng,Gu Xuelin,Hu Caizhi,et al.Failure analysis of sucker rod string on surface driven single screw pump system[J].China Petroleum Machinery,2000,28(4):26-27.

[5]师国臣，陈卓如，李修文．螺杆泵采油井杆柱断脱机理及其对策[J]．石油机械，2000,28(9):42-45．

Shi Guochen,Chen Zhuoru,Li Xiuwen.Causes and countermeasures of failure of rod string in screw pump wells[J].China Petroleum Machinery,2000,28(9):42-45.

[6]王伟章，闫相祯，王海文，等．螺杆泵井驱动杆柱的偏磨和断裂动力学分析[J].石油大学学报：自然科学版，2008，32(2):97-100．

Wang Weizhang,Yan Xiangzhen,Wang Haiwen,et al.Dynamics analysis on partial abrasion and fracture of driving rod in screw pump wells[J].Journal of China University of Petroleum：Edition of Natural Science,2008,32(2):97-100．

[7]刘巨保，罗敏，李淑红．地面驱动螺杆泵抽油杆柱动力学分析技术及其应用[J]．石油学报，2005,26(1):121-124．

Liu Jubao,Luo Min,Li Shuhong.Dynamics analysis technology for rod string of surface driving screw pump and its application in Daqing Oilfield[J].Acta Petrolei Sinica,2005,26(1):121-124.

[8]吕彦平，吴晓东，李远超．单螺杆泵采油系统杆柱瞬态动力学模型及应用[J]．西安石油大学学报：自然科学版，2006，28(4):87-90．

Lü Yanping,Wu Xiaodong,Li Yuanchao.Transient dynamic model of the rod string of single-screw pump oil production system rod and its application[J].Journal of Xi’an Shiyou University：Naturnal Science Edition,2006,28(4):87-90.

[9]陈德春，李兆文，吴晓东．地面驱动螺杆泵采油系统抽油杆柱运动模型[J]．石油大学学报：自然科学版，1999，23(1):42-44．

Chen Dechun,Li Zhaowen,Wu Xiaodong.Kinematic model for rod strings of screw pump in surface drive pumping system[J].Journal of the University of Petroleum,China：Edition of Natural Science,1999,23(1):42-44.

[10]姚春东，董世民，吴长杰，等．定向井杆管接触状态的有限元仿真模型[J]．石油机械，2010，38(11):28-32． 

Yao Chundong,Dong Shimin,Wu Changjie,et al.A finite element simulation model of the rod-tubing contact state in directional wells[J].China Petroleum Machinery,2010,38(11):28-32．

[11]吴晓东，吕彦平，李远超，等．单螺杆泵斜井抽油杆柱运动模型[J]．石油钻探技术，2006，34(3):1-4．

Wu Xiaodong，Lü Yanping，Li Yuanchao，et al.Pumping rod movement model in deviated wells using single progressive cavity pump[J].Petroleum Drilling Technique,2006,34(3):1-4.

[12]吴志坚，吴筱坚．地面驱动式单螺杆泵抽油杆的动力学特性[J]．石油大学学报：自然科学版，2000，24(5):71-73．

Wu Zhijian，Wu Xiaojian.Dynamics characteristics of the ground screw driver sucker rod[J].Journal of the University of Petroleum, China：Edition of Natural Science，2000,24(5):71-73.

[13]李淑红，付军梅，金力杨．螺杆泵抽油杆柱的动态受力分析与工艺设计[J]．钻采工艺，2003，26(2):61-64．

Li Shuhong，Fu Junmei，Jin Liyang.Dynamic mechanical study and process design of screw pumping rod[J].Drilling & Production Technology，2003,26(2):61-64.

[14]吕彦平，吴晓东，李远超．单螺杆泵井抽油杆柱的有限元分析[J]．油气田地面工程，2006，25(2):54．

Lü Yanping，Wu Xiaodong，Li Yuanchao.Finite element analysis of sucker rod with single screw pumps[J].Oil-Gasfield Surface Engineering,2006,25(2):54.

[15]张学鸿，董振刚，张雄，等．探井水平井整体钻柱摩阻力分析的间隙元法[J]．石油学报，2002,23(5):105-109．

Zhang Xuehong,Dong Zhengang,Zhang Xiong.The gap finite element method for analyzing frictional resistance of drilling string in the prospecting horizontal well[J].Acta Petrolei Sinica,2002,23(5):105-109.

[16]张学鸿，刘巨保，陈抡元，等．定向井钻柱二维静力分析的间隙元法[J]．大庆石油学报学报，1992,16(1):53-57．

Zhang Xuehong,Liu Jubao,Chen Lunyuan,et al.Two-dimensional static mechanical analysis using the gap element method in directional drill-string[J].Journal of Daqing Petroleum College,1992,16(1):53-57.

直井地面驱动螺杆泵采油杆管偏磨机理

Mechanism of eccentric wear between rod string and tubing string of a surface driving screw pump lifting system in vertical wells

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 14

编辑推荐

Metrics

本文评价

[1]	董世民, 王宏博. 定向井抽油杆柱横向振动仿真模型及扶正器布点优化[J]. 石油学报, 2020, 41(12): 1686-1696.
[2]	王宏博, 董世民, 甘庆明, 辛红, 朱葛. 低产抽油机井动态参数仿真模型与提高系统效率的途径[J]. 石油学报, 2018, 39(11): 1299-1307.
[3]	金浩, 张来斌, 梁伟, 叶迎春, 丁其坤. 天然气管道泄漏声源特性及传播机理数值模拟[J]. 石油学报, 2014, 35(1): 172-177.
[4]	江雪源董加宇李宜强 . 驱油FPS-B剂的表界面化学性能和微观驱油机理[J]. 石油学报, 2012, 33(6): 1023-1027.
[5]	王文昌狄勤丰姚建林窦升军游红娟. 三维定向井抽油杆柱力学特性有限元分析新方法[J]. 石油学报, 2010, 31(6): 1018-1023.
[6]	董世民张喜顺吴长杰郭吉民. 抽油机井区块整体节能参数仿真优化方法[J]. 石油学报, 2010, 31(3): 475-479.
[7]	刘金梅, 周国强, 韩国有. 基于有限元动力模型的在役钻机井架仿真模型[J]. 石油学报, 2009, 30(5): 788-792.
[8]	吴德会, 黄松岭, 赵伟, 辛君君. 油气长输管道裂纹漏磁检测的瞬态仿真分析[J]. 石油学报, 2009, 30(1): 136-140.
[9]	董世民, 王胜杰, 卢东风, 姬生柱, 侯维前, 王希涛. 定向井有杆抽油系统抽汲参数的优化设计和仿真模型[J]. 石油学报, 2008, 29(1): 120-123.
[10]	韩东颖, 李子丰, 周国强. 在役石油钻机井架极限承载仿真模型研究[J]. 石油学报, 2007, 28(2): 120-123,128.
[11]	李红南, 王德军. 油藏动态模型和剩余油仿真模型[J]. 石油学报, 2006, 27(5): 83-87,91.
[12]	徐守余, 朱连章, 王德军. 微观剩余油动态演化仿真模型研究[J]. 石油学报, 2005, 26(2): 69-72.
[13]	杨海滨, 狄勤丰, 王文昌. 抽油杆柱与油管偏磨机理及偏磨点位置预测[J]. 石油学报, 2005, 26(2): 100-103.
[14]	金国梁, 陈琳. 抽油杆的变形分析及滚轮接箍的合理配置[J]. 石油学报, 1990, 11(2): 106-116.