胜利油田超稠油油藏蒸汽驱三维物理模拟与应用

doi:10.7623/syxb201304014

石油学报 ›› 2013, Vol. 34 ›› Issue (4): 733-739.DOI: 10.7623/syxb201304014

胜利油田超稠油油藏蒸汽驱三维物理模拟与应用

曹嫣镔^1,2, 刘冬青², 王善堂², 于田田², 夏道宏¹

1. 中国石油大学化学工程学院山东青岛 266580;
2. 中国石化胜利油田分公司采油工艺研究院山东东营 257000

收稿日期:2012-12-25 修回日期:2013-03-20 出版日期:2013-07-25 发布日期:2013-07-04
通讯作者: 曹嫣镔
作者简介:曹嫣镔,男,1975年5月生,1996年毕业于山东工业大学,2005年获山东大学理学硕士学位,现为中国石油大学(华东)博士研究生、中国石化胜利油田分公司采油工艺研究院高级工程师,主要从事稠油开采技术研究。Email:caoyanbin177.slyt@sinopec.com
基金资助:
国家重大科技专项(2011ZX05011-002)资助。

3D physical simulation of steam flooding and applications in ultra-heavy oil reservoirs of Shengli oilfield

CAO Yanbin^1,2, LIU Dongqing², WANG Shantang², YU Tiantian², XIA Daohong¹

1. College of Chemical Engineering, China University of Petroleum, Qingdao 266580 China;
2. Oil Production Technology Research Institute, Sinopec Shengli Oilfield Company, Dongying 257000, China

Received:2012-12-25 Revised:2013-03-20 Online:2013-07-25 Published:2013-07-04

摘要/Abstract

摘要：

针对胜利油田单56区块油藏条件,利用蒸汽驱三维物理模拟装置,开展了20% 、40% 、60% 蒸汽干度条件下反九点井网超稠油油藏蒸汽驱实验。分析了单井及井组生产动态,并在蒸汽驱的基础上研究了采用氮气泡沫的方式改善超稠油蒸汽驱的开发效果。实验结果表明,超稠油油藏汽窜较为严重,综合含水上升较快,蒸汽腔发育不均匀;边井生产效果较好,角井温度场发育较差,产液量和产油量较低,对井组贡献率较低。通过提高蒸汽干度可以有效提高蒸汽驱阶段的采收率,当注入油藏蒸汽干度从20% 提高到60%,蒸汽驱阶段的采出程度提高19.86%。段塞注入0.093 PV的泡沫体系时,蒸汽汽窜得到有效抑制,边井产液量和综合含水均出现明显下降,角井温度场开始发育,角井产液量和产油量显著增加,阶段综合含水下降7%,提高采收率15% 以上。通过提高蒸汽干度和辅助氮气泡沫调剖工艺,超稠油油藏可以转为蒸汽驱进一步提高采收率。

关键词: 蒸汽驱, 超稠油, 三维物模, 泡沫, 蒸汽干度, 汽窜, 含水率, 蒸汽腔

Abstract:

A three-dimensional physical simulation on steam flooding of ultra-heavy oil reservoirs for an inverted nine-spot well network was designed according to reservoir conditions of the Shan-56 block in the Shengli oilfield and conducted under conditions of the 20%, 40% and 60% steam dryness respectively, in order to analyze the production status of a single well or well group and improve recovery effects of ultra-heavy oil reservoirs by nitrogen foam injection on the basis of steam flooding. The experimental results show that the steam channeling of ultra-heavy oil reservoirs is relatively severe, the comprehensive water cut rises fast and steam chambers develop unevenly. Edge wells have an increase in production, while corner wells show a poor temperature growth and low level both liquid and crude production, thus contributing a little to the well group output. The steam flooding recovery could be enhanced remarkably by increasing the steam dryness, for instance, the displacement efficiency of steam flooding increased by 19.86% when the dryness of injected steam rose from 20% to 60%. When slug injection was a 0.093 PV foam system on the basis of steam flooding, the steam channeling could be effectively suppressed along with a remarkable decrease in both the liquid production and comprehensive water cut of edge wells. Moreover, a temperature field around corner wells began to develop along with a significant increase in both the liquid and crude production, the comprehensive water cut of intervals decreased by 7%, while the recovery ratio was enhanced by over 15%. Therefore, the enhanced oil recovery of ultra-heavy oil reservoirs can be further increased by increasing the steam dryness in steam flooding associated with an auxiliary profile control technique, nitrogen foam injection.

Key words: steam flooding, ultra-heavy oil, 3D physical simulation, foam, steam dryness, steam channeling, water cut, steam chamber

中图分类号:

TE357

曹嫣镔, 刘冬青, 王善堂, 于田田, 夏道宏. 胜利油田超稠油油藏蒸汽驱三维物理模拟与应用[J]. 石油学报, 2013, 34(4): 733-739.

CAO Yanbin, LIU Dongqing, WANG Shantang, YU Tiantian, XIA Daohong. 3D physical simulation of steam flooding and applications in ultra-heavy oil reservoirs of Shengli oilfield[J]. Editorial office of ACTA PETROLEI SINICA, 2013, 34(4): 733-739.

参考文献

[1] 刘文章.稠油注蒸汽热采工程[M].北京:石油工业出版社,1997:455-470.

Liu Wenzhang.The projection of steam injection for thermal recovery of the heavy oil reservoir[M].Beijing:Petroleum Industry Press,1997:455-470.

[2] 张义堂,陈亚平,刘尚奇,等.热力采油提高采收率技术[M].北京:石油工业出版社,2006:20-24.

Zhang Yitang,Chen Yaping,Liu Shangqi,et al.EOR technologyby thermal recovery[M].Beijing:Petroleum Industry Press,2006:22-24.

[3] 张义堂,李秀峦,张霞.稠油蒸汽驱方案设计及跟踪调整四项基本准则[J].石油勘探与开发,2008,35(6):715-721.

Zhang Yitang,Li Xiuluan,Zhang Xia,et al.Four fundamental principles for desigh and follow-up of steam flooding in heavy oil reservoirs[J].Petroleum Exploration and Development,2008,35(6):715-721.

[4] 石启新,方开璞.注蒸汽开发经济极限油汽比及经济可采储量的计算方法及应用[J].石油勘探与开发,2001,28(4):97-98.

Shi Qixin,Fang Kaipu.The calculating method and application of economic limiting steam/oil ratio for steam flood and steam soak[J].Petroleum Exploration and Development,2001,28(4):97-98.

[5] 关文龙,吴淑红,蒋有伟,等.高含水油藏转注蒸汽三维物理模拟研究[J].石油学报,2009,30(3):404-408.

Guan Wenlong,Wu Shuhong,Jiang Youwei,et al.3D physical model of steam injection in high water cut reservoir[J].Acta Petrolei Sinica,2009,30(3):404-408.

[6] 张忠义,周游,沈德煌,等.直井-水平井组合蒸汽氮气泡沫驱物模实验[J].石油学报,2012,33(1):90-95.

Zhang Zhongyi,Zhou You,Shen Dehuang,et al.Physical modeling experiments on steam nitrogen foam flooding for a vertical and horizontal well combination[J].Acta Petrolei Sinica,2012,33(1):90-95.

[7] 杨元亮.胜利单56超稠油油藏蒸汽驱先导性试验[J].石油天然气学报,2011,33(1):142-144.

Yang Yuanliang.Pilot test of steam flooding in super heavy oil reservoirs in Shan 56 area[J].Journal of Oil and Gas Technology,2011,33(1):142-144.

[8] Pujol L,Boberg T C.Scaling accuracy of laboratory steam flooding models[R].SPE 4191,1972.

[9] 袁士义,刘尚奇,张义堂,等.热水添加氮气泡沫驱提高稠油采收率研究[J].石油学报,2004,25(1):57-65.

Yuan Shiyi,Liu Shangqi,Zhang Yitang,et al.Enhancing heavy oil recovery with hot water flooding by adding nitrogen and surfactant[J].Acta Petrolei Sinica,2004,25(1):57-65.

[10] 吕广忠,朱桂芳,张建乔,等.氮气泡沫热水驱物理模拟及数值模拟研究[J].石油钻采工艺,2007,29(4):75-79.

Lü Guangzhong,Zhu Guifang,Zhang Jianqiao,et al.Research on physical and numerical simulation of nitrogen hot-water foam flooding[J].Oil Drilling & Production Technology,2007,29(4):75-79.

[11] Kular G S,Lowe K,Cmmbe D.Foam application in an oil sands steamflood process[R].SPE 19690,1989.

[12] 范治成,刘慧卿,张红玲,等.井楼油田稠油油藏氮气泡沫调剖室内实验[J].石油钻采工艺,2007,29(4):75-79.

Fan Zhicheng,Liu Huiqing,Zhang Hongling,et al.Laboratory study of nitrogen-foam agents profile control technology at heavy oil reservoir in Jinglou oilfield[J].Oil Drilling & Production Technology,2007,29(4):75-79.

[13] 马昌明,刘建山,郝英敏.化学添加剂提高蒸汽吞吐效果室内研究[J].石油钻采工艺,2003,25(8):14-16.

Ma Changming,Liu Jianshan,Hao Yingmin.Experiment on chemical additives to improve effict of steam soaking[J].Oil Drilling & Production Technology,2003,25(8):14-16.

[14] 宫俊峰,曹嫣镔,唐培忠,等.高温复合泡沫体系提高胜利油田稠油热采开发效果[J].石油勘探与开发,2006,33(2):212-216.

Gong Junfeng,Cao Yanbin,Tang Peizhong,et al.Improving development efficiency of heavy oil in Shengli oilfield by using high-temperature compounded foaming agent[J].Petroleum Exploration and Development,2006,33(2):212-216.

[15] 曹嫣镔,郭省学,唐培忠,等.伴蒸汽注入化学剂提高采收率的室内研究[J].油气采收率技术,2000,7(4):16-19.

Cao Yanbin,Guo Shengxue,Tang Peizhong,et al.Laboratory study of improved oil recovery by chemical agent injection with steam[J].Petroleum Geology and Recovery Efficiency,2000,7(4):16-19.

胜利油田超稠油油藏蒸汽驱三维物理模拟与应用

3D physical simulation of steam flooding and applications in ultra-heavy oil reservoirs of Shengli oilfield

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	李晓光. 辽河坳陷欢喜岭油田稠油成藏条件及勘探开发关键技术[J]. 石油学报, 2021, 42(4): 541-560.
[2]	魏兵, 陈神根, 赵金洲, 蒲万芬, 魏发林, 相华, Kadet Valeriy. 纳米纤维高稳泡沫在裂缝中的生成和运移规律[J]. 石油学报, 2020, 41(9): 1135-1145.
[3]	瞿超超, 刘正中, 殷鸿尧, 鲁光亮, 李祖友, 冯玉军. 新型排水采气用抗凝析油泡排剂[J]. 石油学报, 2020, 41(7): 865-874.
[4]	刘静, 夏军勇, 刘玺, 吴飞鹏, 蒲春生. 低频波对泡沫稳定性协同强化效应[J]. 石油学报, 2020, 41(5): 584-591.
[5]	郭玲玲, 刘涛, 刘影, 郎成山, 胡绍彬. 蒸汽驱中—后期间歇注热理论模型与现场试验[J]. 石油学报, 2019, 40(7): 823-829.
[6]	胡志强, 杨进, 路保平, 侯绪田, 黄小龙, 巩立根, 李文龙, 李舒展. 深水泡沫套管静水压载特性与压力控制机理[J]. 石油学报, 2019, 40(6): 726-733.
[7]	杨怀军, 潘红, 章杨, 钟显康. 减氧对空气泡沫驱井下管柱的缓蚀作用及减氧界限[J]. 石油学报, 2019, 40(1): 99-107.
[8]	张振楠, 孙宝江, 王志远, 高永海, 许亮斌, 袁凯鹏, 相华. 产液气井泡沫排液起泡能力分析[J]. 石油学报, 2019, 40(1): 108-114.
[9]	杨朝蓬, 李星民, 陈和平, 赵海龙, 包宇, 沈杨, 刘章聪. 泡沫油型超重油冷采后转SAGD开发数值模拟[J]. 石油学报, 2018, 39(4): 445-455.
[10]	胡伟, 吕成远, 王锐, 崔茂蕾, 杨阳, 王欣. 水驱转CO₂混相驱渗流机理及传质特征[J]. 石油学报, 2018, 39(2): 201-207.
[11]	胡绍彬, 徐庆龙, 郭玲玲, 王鹏, 刘少克. 采出液含水对生产气油比的影响规律[J]. 石油学报, 2018, 39(1): 116-121,128.
[12]	苏伟, 侯吉瑞, 李海波, 赵腾, 席园园. 缝洞型碳酸盐岩油藏注氮气泡沫可行性及影响因素[J]. 石油学报, 2017, 38(4): 436-443.
[13]	张康卫, 李宾飞, 袁龙, 李松岩, 刘刚, 骆志敏. 低压漏失井氮气泡沫连续冲砂技术[J]. 石油学报, 2016, 37(S2): 122-130.
[14]	吴川, 张汝生, 张祖国, 孙志宇, 吴正彬. 超稠油改质降黏分子模拟及机理[J]. 石油学报, 2015, 36(3): 355-360.
[15]	吴正彬, 庞占喜, 刘慧卿, 王大为, 王春磊, 王长久, 叶子路, 陈一诺. 稠油油藏高温凝胶改善蒸汽驱开发效果可视化实验[J]. 石油学报, 2015, 36(11): 1421-1426.