钻杆接头多轴疲劳寿命

doi:10.7623/syxb201907008

石油学报 ›› 2019, Vol. 40 ›› Issue (7): 839-845.DOI: 10.7623/syxb201907008

钻杆接头多轴疲劳寿命

张智¹, 祝效华²

1. 成都中腾石油工程技术有限公司四川成都 610500;
2. 西南石油大学机电工程学院四川成都 610500

收稿日期:2018-08-13 修回日期:2019-04-21 出版日期:2019-07-25 发布日期:2019-07-28
通讯作者: 祝效华,男,1978年7月生,2002年获西南石油学院学士学位,2007年获西南石油大学博士学位,现为西南石油大学教授、博士生导师,主要从事井下管柱力学及工具设计方面的研究工作。Email:zxhth113@163.com
作者简介:张智,男,1990年7月生,2013年获攀枝花学院学士学位,2016年获西南石油大学硕士学位,现为成都中腾石油工程技术有限公司工程师,主要从事井下管柱力学及工具设计方面的研究工作。Email:1914001257@qq.com
基金资助:
国家自然科学基金项目（No.51674214）、四川省青年科技创新团队项目（2017TD0014）和四川省科技计划国际合作计划项目（2016HH0008）资助。

Multiaxial fatigue life of drill pipe joint

Zhang Zhi¹, Zhu Xiaohua²

1. Chengdu Zhongteng Petroleum Engineering Technology Co., Ltd., Sichuan Chengdu 610500, China;
2. Mechatronic Engineering School, Southwest Petroleum University, Sichuan Chengdu 610500, China

Received:2018-08-13 Revised:2019-04-21 Online:2019-07-25 Published:2019-07-28

摘要/Abstract

摘要：

在实际钻井过程中，钻杆接头以螺纹连接处的疲劳破坏为主，导致钻井成本显著增加。现有对钻杆接头的研究主要集中于钻杆接头的静力学特性分析，少有涉及钻杆接头的疲劳破坏的研究。基于虚功原理、Von Mises屈服准则及接触非线性理论，考虑螺纹升角的影响，建立了钻杆接头的三维有限元计算模型，分析了钻杆接头的上扣特性及其在复合载荷作用下的力学特性。基于材料S-N曲线，综合考虑尺寸系数、应力集中系数、表面加工系数及表面强化系数的影响，确定了钻杆接头的弯曲疲劳S-N曲线理论模型，通过对比验证建立了满足工程要求的钻杆接头疲劳有限元计算模型。运用多轴疲劳算法，计算了钻杆接头在复合交变载荷下的疲劳寿命，分析了残余应力和表面质量对疲劳寿命的影响。研究结果表明，在上扣扭矩或复合载荷作用下，钻杆接头最大Mises应力均出现在公扣第1有效啮合螺纹牙根处；弯曲井段API钻杆接头的疲劳寿命较小，建议开发适合超深井、水平井、大位移井及大斜度井的专用钻杆接头；残余应力与表面质量对钻杆接头的疲劳寿命影响较大，在钻杆接头螺纹根部引入可控的残余压应力和改善表面质量可以大幅提高其疲劳寿命。

关键词: 钻杆接头, S-N曲线, 残余应力, 表面质量, 疲劳寿命

Abstract:

Fatigue damage mainly occurs at the threaded joints of drill pipe in the actual drilling process, leading to a significant increase in the drilling cost. In recent years, domestic and foreign scholars have done a lot of research on drill pipe joint, but mainly focusing on the analysis of its static characteristics, rarely involving the fatigue failure of drill pipe joint. In view of the above problem, considering the influence of lead angle, a 3D numerical simulation model of drill pipe joint has been created based on virtual work principle, Von Mises yield criterion and nonlinear contact theory, so as to analyze the screw-on feature of drill pipe joint and its mechanical property under composite load. Based on the material S-N curve, a theoretical model on the bending fatigue S-N curve of drill pipe joint has been established by comprehensively considering the influence of size factor, stress concentration factor, surface processing coefficient and surface strengthening coefficient. Through comparison and verification, this study establishes the fatigue finite element calculation model of drill pipe joint meeting the engineering requirements. The fatigue life of drill pipe joint under composite alternating load has been calculated by multi-axis fatigue algorithm to further analyze the effects of residual stress and surface quality on fatigue life. The results show that under the action of the make-up torque or multi-axis load, the maximum Mises stress of drill pipe joint appears at the root of the first effective meshing thread of pin; the fatigue life of API drill pipe joint in curved portion is short. It is recommended to develop suitable special drill pipe joints for ultra-deep wells, horizontal wells, large-displacement wells and high-angle wells; residual stress and surface quality have a great impact on the fatigue life of drill pipe joints. The introduction of controllable residual compressive stresses at the roots of drill pipe joints and the improvement of the surface quality can greatly improve the fatigue life.

Key words: drill pipe joint, S-N curve, residual stress, surface quality, fatigue life

中图分类号:

TE933

张智, 祝效华. 钻杆接头多轴疲劳寿命[J]. 石油学报, 2019, 40(7): 839-845.

Zhang Zhi, Zhu Xiaohua. Multiaxial fatigue life of drill pipe joint[J]. Acta Petrolei Sinica, 2019, 40(7): 839-845.

参考文献

[1] 任辉. API石油钻杆接头应力分析及结构改进研究[D].上海:华东理工大学,2011.
REN Hui.Stress analyses and structure improvement research of API oil tool joint[D].Shanghai:East China University of Science and Technology,2011.
[2] 陈松林.钻杆螺纹失效分析及改进措施研究[D].重庆:重庆大学,2008.
CHEN Songlin.Drill pipe thread failure analysis and research measures to improve[D].Chongqing:Chongqing University,2008.
[3] ZHU Xiaohua,DONG Liangliang,TONG Hua.Failure analysis and solution studies on drill pipe thread gluing at the exit side of horizontal directional drilling[J].Engineering Failure Analysis,2013,33(5):251-264.
[4] 明鑫,练章华,林铁军,等.气体携岩对钻杆接头冲蚀规律研究[J].西南石油大学学报:自然科学版,2014,36(3):173-178.
MING Xin,LIAN Zhanghua,LIN Tiejun,et al.Study on the erosion law of gas with cuttings against tool joint[J].Journal of Southwest Petroleum University:Science & Technology Edition,2014,36(3):173-178.
[5] 庄泳,鲁喜宁,高连新,等.气密钻杆接头受力分析与紧扣圈数优选[J].石油机械,2015,43(7):30-35.
ZHUANG Yong,LU Xining,GAO Lianxin,et al.Force analysis and fastening turns optimization of airtight drill pipe joint[J].China Petroleum Machinery,2015,43(7):30-35.
[6] AKYILDIZ H K,LIVATYALI H.Effects of machining parameters on fatigue behavior of machined threaded test specimens[J].Materials & Design,2010,31(2):1015-1022.
[7] VAN WITTENBERGHE J,DE BAETS P,DE WAELE W,et al.Evaluation of fatigue crack propagation in a threaded pipe connection using an optical dynamic 3D displacement analysis technique[J].Engineering Failure Analysis,2011,18(3):1115-1121.
[8] 祝效华,张智,常学军,等.复杂结构井磨损套管连接螺纹的三维力学行为[J].石油学报,2015,36(6):748-753.
ZHU Xiaohua,ZHANG Zhi,CHANG Xuejun,et al.Three-dimensional mechanical behavior of worn casing connecting thread in complex structural well[J].Acta Petrolei Sinica,2015,36(6):748-753.
[9] 祝效华,刘伟吉.单齿高频扭转冲击切削的破岩及提速机理[J].石油学报,2017,38(5):578-586.
ZHU Xiaohua,LIU Weiji.The rock breaking and ROP rising mechanism for single-tooth high-frequency torsional impact cutting[J].Acta Petrolei Sinica,2017,38(5):578-586.
[10] 祝效华,刘伟吉.旋冲钻井技术的破岩及提速机理[J].石油学报,2018,39(2):216-222.
ZHU Xiaohua,LIU Weiji.Rock breaking and ROP rising mechanism of rotary-percussive drilling technology[J].Acta Petrolei Sinica,2018,39(2):216-222.
[11] 贾曦雨,王树山,马峰,等.射孔冲击相变对射孔套管抗挤性能的影响[J].石油学报,2017,38(3):348-355.
JIA Xiyu,WANG Shushan,MA Feng,et al.Influence of perforation shock-induced phase transformation on the collapsing strength of perforated casing[J].Acta Petrolei Sinica,2017,38(3):348-355.
[12] 赵传伟,王绍先,裴学良,等.计数式全通径压裂滑套优化设计[J].石油学报,2018,39(4):482-490.
ZHAO Chuanwei,WANG Shaoxian,PEI Xueliang,et al.Optimization design of counter-type full-bore fracturing sliding-sleeve[J].Acta Petrolei Sinica,2018,39(4):482-490.
[13] 李群生,王希勇,林铁军,等.气体钻井API钻铤螺纹多轴疲劳寿命研究[J].石油钻采工艺,2014,36(3):56-58.
LI Qunsheng,WANG Xiyong,LIN Tiejun,et al.Research on multiaxial fatigue life of API drill collar thread in gas drilling[J].Oil Drilling & Production Technology,2014,36(3):56-58.
[14] KANDIL F A,BROWN M W,MILLER K J.Biaxial low-cycle fatigue failure of 316 stainless steel at elevated temperatures[C]//Mechanical Behaviour and Nuclear Applications of Stainless Steel at Elevated Temperatures. London:The Metals Society,1982.
[15] 尚德广,王德俊.多轴疲劳强度[M].北京:科学出版社,2007.
SHANG Deguang,WANG Dejun.Multiaxial fatigue strength[M].Beijing:Science Press,2007.
[16] 陈勇,练章华,唐玉宏,等.NC50型钻铤公螺纹疲劳寿命计算分析[J].石油矿场机械,2006,35(4):58-60.
CHEN Yong,LIAN Zhanghua,TANG Yuhong,et al.The fatigue life calculation of pin thread on NC50 drill collar[J].Oil Field Equipment,2006,35(4):58-60.
[17] 庄茁,由小川,廖剑辉,等.基于ABAQUS的有限元分析和应用[M].北京:清华大学出版社,2009.
ZHUANG Zhuo,YOU Xiaochuan,LIAO Jianhui,et al.Finite element analysis and applications based on ABAQUS[M].Beijing:Tsinghua University Press,2009.
[18] API.Specification for threading and gauging of rotary shouldered thread connections:API Spec 7-2[S].American Petroleum Institute,2008.
[19] 张智.复杂结构井钻杆接头三维力学特性及结构改进研究[D].成都:西南石油大学,2016.
ZHANG Zhi.Study on the three-dimensional mechanical property and structural improvement of drill pipe joint in complex well[D].Chengdu:Southwest Petroleum University,2016.
[20] 狄勤丰,陈锋,王文昌,等.双台肩钻杆接头三维力学分析[J].石油学报,2012,33(5):871-877.
DI Qinfeng,CHEN Feng,WANG Wenchang,et al.Three-dimensional mechanical analysis of the double-shouldered tool joint[J].Acta Petrolei Sinica,2012,33(5):871-877.
[21] 王琍,张汝忻,邹家祥,等.API圆螺纹套管接头应力场分布实验[J].北京科技大学学报,2000,22(6):555-558.
WANG Li,ZHANG Ruxin,ZOU Jiaxiang,et al.Experimental research of stress field distribution on API round thread casing connection[J].Journal of University of Science and Technology Beijing,2000,22(6):555-558.
[22] 胡辛禾,BALLEY E I.钻杆接头用的螺纹脂试验[J].国外石油机械,1994,5(2):68-72.
HU Xinhe,BALLEY E I.Thread grease test of drill pipe joint[J].Foreign Petroleum Machinery,1994,5(2):68-72.
[23] 王国军.Msc.Fatigue疲劳分析实例指导教程[M].北京:机械工业出版社,2009.
WANG Guojun.Msc.Fatigue fatigue analysis examples guide tutorial[M].Beijing:China Machine Press,2009.
[24] 秦大同,谢里阳.疲劳强度与可靠性设计[M].北京:化学工业出版社,2013.
QIN Datong,XIE Liyang.Fatigue strength and reliability design[M].Beijing:Chemical Industry Press,2013.
[25] 李鹤林,李平全,冯耀荣.石油钻柱失效分析及预防[M].北京:石油工业出版社,1999.
LI Helin,LI Pingquan,FENG Yaorong.Failure analysis and prevention of oil drill string[M].Beijing:Petroleum Industry Press,1999.

钻杆接头多轴疲劳寿命

Multiaxial fatigue life of drill pipe joint

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 4

编辑推荐

Metrics

本文评价

[1]	韩文海, 周晶. 腐蚀海底管道可靠性分析[J]. 石油学报, 2015, 36(4): 516-520.
[2]	李子丰　李雪娇　王　鹏. 预弯曲连续油管及其疲劳寿命预测[J]. 石油学报, 2012, 33(4): 706-710.
[3]	战人瑞, 陶春达. 自增强设备最佳超应变度研究[J]. 石油学报, 1996, 17(4): 128-136.
[4]	李广铎, 刘国山, 刘柏梁, 侯贤忠, 郭其安. 十万立方米浮顶式原油贮罐焊接残余应力分布规律的研究[J]. 石油学报, 1991, 12(1): 99-106.