多点注汽水平井井筒出流规律数值模拟

doi:10.7623/syxb201706009

石油学报 ›› 2017, Vol. 38 ›› Issue (6): 696-704.DOI: 10.7623/syxb201706009

多点注汽水平井井筒出流规律数值模拟

陈会娟¹, 李明忠², 狄勤丰¹, 刘春苗³

1. 上海大学上海市应用数学和力学研究所上海 200072;
2. 中国石油大学石油工程学院山东青岛 266580;
3. 中海油能源发展股份有限公司上海工程技术分公司上海 200335

收稿日期:2016-08-29 修回日期:2017-02-13 出版日期:2017-06-25 发布日期:2017-07-08
通讯作者: 狄勤丰,男,1963年8月生,1984年获石油大学(华东)钻井工程专业学士学位,1997年获西南石油学院油气井工程专业博士学位,现为上海大学教授、博士生导师,主要从事石油工程中的力学问题研究。Email:qinfengd@sina.com
作者简介:陈会娟,女,1987年4月生,2009年获中国石油大学(华东)石油工程专业学士学位,2015年获中国石油大学(华东)油气田开发工程专业博士学位,现为上海大学博士后,主要从事油气田开发工程方面的研究。Email:iichj@126.com
基金资助:
国家重大科技专项（2011ZX05024-005）和中央高校基本科研业务费专项资金项目（14CX06025A）资助。

Numerical simulation of the outflow performance for horizontal wells with multiple steam injection valves

Chen Huijuan¹, Li Mingzhong², Di Qinfeng¹, Liu Chunmiao³

1. Shanghai Institute of Applied Mathematics and Mechanics, Shanghai University, Shanghai 200072, China;
2. School of Petroleum Engineering, China University of Petroleum, Shandong Qingdao 266580, China;
3. CNOOC EnerTech-Shanghai Drilling & Producing Branch, Shanghai 200335, China

Received:2016-08-29 Revised:2017-02-13 Online:2017-06-25 Published:2017-07-08

摘要/Abstract

摘要：

基于多点注汽水平井管柱结构，考虑注入蒸汽在水平井筒内的变质量流特性及注汽阀节流压差的影响，建立了多点注汽水平井井筒与储层耦合数学模型，并采用迭代方法对其进行了求解；以此为基础，系统研究了多点注汽水平井井筒出流规律。结果表明：多点注汽水平井注汽过程中，水平段油管内压力、温度和蒸汽干度从水平井跟端到趾端逐渐降低，但压力和温度降低幅度并不显著，蒸汽干度降低幅度较为明显；蒸汽注入量与注汽阀节流压差沿水平段均呈不对称的"U"型分布，且随着时间的增加，蒸汽注入量沿水平井段的不均匀性越来越严重，蒸汽注入量不均匀系数越来越大；通过调整注汽阀沿水平井段泄流面积可以在一定程度上减缓蒸汽沿水平井筒的不均匀注入。

关键词: 多点注汽, 水平井, 注汽阀, 耦合模型, 出流规律

Abstract:

Based on the string structure of horizontal wells with multiple steam injection valves and in consideration of the variable mass flow of injected steam in horizontal wellbore as well as the impacts from throttle differential pressure of steam injection valve, a coupled reservoir-wellbore model of horizontal well with multiple steam injection valves were established and solved using an iterative method. On this basis, the outflow performance of horizontal wellbore with multiple steam injection valves were systematically studied. The results show that the pressure, temperature and steam quality in the tube of horizontal section gradually drop from the wellbore heel to toe in the multipoint steam injection process of horizontal wells. Moreover, the decrease of pressure and temperature is insignificant, while that of steam quality is more obvious. The steam injection rate and the throttle differential pressure of steam injection valve present the "U"-shaped asymmetrical distribution along the horizontal section. In addition, with the time increasing, the non-uniformity of steam injection rate along the horizontal wellbore is intensified, and the non-uniformity coefficient is becoming greater. The non-uniform injection of steam along horizontal wellbore can be slowed down to a certain extent by adjusting the drainage area of steam injection valves.

Key words: multipoint steam injection, horizontal well, steam injection valve, coupled model, outflow performance

中图分类号:

TE345

陈会娟, 李明忠, 狄勤丰, 刘春苗. 多点注汽水平井井筒出流规律数值模拟[J]. 石油学报, 2017, 38(6): 696-704.

Chen Huijuan, Li Mingzhong, Di Qinfeng, Liu Chunmiao. Numerical simulation of the outflow performance for horizontal wells with multiple steam injection valves[J]. Acta Petrolei Sinica, 2017, 38(6): 696-704.

参考文献

[1] 刘文超,同登科,张世明,等.低渗透稠油油藏水平井产能计算新方法[J].石油学报,2010,31(3):458-462.
LIU Wenchao,TONG Dengke,ZHANG Shiming,et al.A new method for calculating productivity of horizontal well in low-permeability heavy oil reservoir[J].Acta Petrolei Sinica,2010,31(3):458-462.
[2] 刘春泽,程林松,刘洋,等.水平井蒸汽吞吐加热半径和地层参数计算模型[J].石油学报,2008,29(1):101-105.
LIU Chunze,CHENG Linsong,LIU Yang,et al.Calculating models for heating radius of cyclic steam stimulation and formation parameters in horizontal well after soaking[J].Acta Petrolei Sinica,2008,29(1):101-105.
[3] 刘忠能,钟海全,李颖川,等.稠油环空掺稀气举技术——以吐哈油田吐玉克区块为例[J].石油学报,2015,36(2):217-223.
LIU Zhongneng,ZHONG Haiquan,LI Yingchuan,et al.Heavy oil gas-lift technology assisted with light oil:a case study from Tuyuk block in Tuha oilfield[J].Acta Petrolei Sinica,2015,36(2):217-223.
[4] 宗艳波,王磊,史晓锋.SAGD成对水平井磁导向测距仪研制与应用[J].石油学报,2016,37(11):1428-1434.
ZONG Yanbo,WANG Lei,SHI Xiaofeng.Development and application of magnetic positioning system for SAGD pairing horizontal well[J].Acta Petrolei Sinica,2016,37(11):1428-1434.
[5] 李萍,刘志龙,邹剑,等.渤海旅大27-2油田蒸汽吞吐先导试验注采工程[J].石油学报,2016,37(2):242-247.
LI Ping,LIU Zhilong,ZOU Jian,et al.Injection and production project of pilot test on steam huff-puff in oilfield LD27-2,Bohai Sea[J].Acta Petrolei Sinica,2016,37(2):242-247.
[6] 何聪鸽,穆龙新,许安著,等.稠油油藏蒸汽吞吐加热半径及产能预测新模型[J].石油学报,2015,36(12):1564-1570.
HE Congge,MU Longxin,XU Anzhu,et al.A new model of steam soaking heating radius and productivity prediction for heavy oil reservoirs[J].Acta Petrolei Sinica, 2015,36(12):1564-1570.
[7] 白文海.辽河金马油田水平井有效注汽技术[J].石油钻采工艺,2010,32(1):116-119.
BAI Wenhai.Effective horizontal well steam injection technology in Jinma oilfield of Liaohe[J].Oil Drilling & Production Technology,2010,32(1):116-119.
[8] 刘德铸.稠油水平井均匀注汽技术[J].特种油气藏,2014,21(5):127-129.
LIU Dezhu.Uniform steam injection technology for heavy oil horizontal wells[J].Special Oil & Gas Reservoirs,2014,21(5):127-129.
[9] 李金发,栾智勇,赵晓红,等.水平井均衡注汽技术[J].钻采工艺,2013,36(6):48-50.
LI Jinfa,LUAN Zhiyong,ZHAO Xiaohong,et al.Uniform steam injection technology of horizontal well[J].Drilling & Production Technology,2013,36(6):48-50.
[10] 陈治军.均匀注汽工艺技术研究[J].新疆石油天然气,2012,8(增刊1):1-5.
CHEN Zhijun.Study on uniform steam injection technology[J].Xinjiang Oil & Gas,2012,8(S1):1-5.
[11] 薛世峰,王海静,朱桂林,等.改善水平井吸汽剖面的计算模型[J].特种油气藏,2008,15(5):94-96.
XUE Shifeng,WANG Haijing,ZHU Guilin,et al.Calculation model of improving steam injection profile of horizontal wells[J].Special Oil & Gas Reservoirs,2008,15(5):94-96.
[12] 薛世峰,王海静.水平井均匀注汽工艺研究及软件开发[J].石油矿场机械,2009,38(1):38-41.
XUE Shifeng,WANG Haijing.Study of uniform steam injection technology in horizontal well and software development[J].Oil Field Equipment,2009,38(1):38-41.
[13] 陈新民.水平井均匀注汽工艺在滨南油田的研究与应用[J].油气地质与采收率,2009,16(2):106-107.
CHEN Xinmin.Research and application of uniform steam injection in the horizontal wells,Binnan oilfield[J].Petroleum Geology and Recovery Efficiency,2009,16(2):106-107.
[14] 朱秀星,薛世峰,仝兴华,等.热采水平井多点注汽工具设计与试验研究[J].石油矿场机械,2012,41(10):24-28.
ZHU Xiuxing,XUE Shifeng,TONG Xinghua,et al.Design and experimental research of muitipoint steam injection tool used in horizontal well thermal recovery[J].Oil Field Equipment,2012,41(10):24-28.
[15] 尹虎,刘辉,李黔,等.提高稠油水平井注蒸汽效率的技术研究[J].石油天然气学报,2011,33(12):119-123.
YIN Hu,LIU Hui,LI Qian,et al.Technical research on improving efficiency of steam injection in horizontal wells for heavy oil reservoirs[J].Journal of Oil and Gas Technology,2011,33(12):119-123.
[16] GAI Pingyuan,DU Yongbin,LU Guocheng,et al.Uniform steam injection technology used in thermal horizontal wells[R].SPE 130893,2010.
[17] 陈会娟,李明忠,王一平,等.割缝筛管水平井注蒸汽热力参数分布规律数值模拟研究[J].石油钻探技术,2015,43(3):109-115.
CHEN Huijuan,LI Mingzhong,WANG Yiping,et al.Numerical simulation in steam injection wells for optimizing the distribution of thermal parameters in horizontal wells with slotted liners[J].Petroleum Drilling Techniques,2015,43(3):109-115.
[18] 吴永彬,李秀峦,孙新革,等.双水平井蒸汽辅助重力泄油注汽井筒关键参数预测模型[J].石油勘探与开发,2012,39(4):481-488.
WU Yongbin,LI Xiuluan,SUN Xin'ge,et al.Key parameters forecast model of injector wellbores during the dual-well SAGD process[J].Petroleum Exploration and Development,2012,39(4):481-488.
[19] BEGGS H D,BRILL J P.A study of two-phase flow in inclined pipes[J].Journal of Petroleum Technology, 1973,25(5):607-617.
[20] 陈月明.注蒸汽热力采油[M].东营:石油大学出版社, 1996:64-85.
CHEN Yueming.Thermal recovery of steam injection[M].Dongying:Press of University of Petroleum,1996:64-85.
[21] LI Mingzhong,CHEN Huijuan,ZHANG Yanyu,et al.A coupled reservoir/wellbore model to simulate the steam injection performance of horizontal wells[J].Energy Technology,2015,3(5):535-542.
[22] 王一平,李明忠,高晓,等.注蒸汽水平井井筒内参数计算新模型[J].西南石油大学学报:自然科学版,2010,32(4):127-133.
WANG Yiping,LI Mingzhong,GAO Xiao,et al.A new parameter-cauculating model for steam flooding in horizontal wellbore[J].Journal of Southwest Petroleum University:Science & Technology Edition,2010,32(4):127-133.
[23] ELTAHER E K,MURADOV K,DAVIES D R,et al.Autonomous inflow control valves-their modelling and "Added valve"[R].SPE 170780,2014.
[24] 李明忠,陈会娟,张贤松,等.煤层气多分支水平井井筒压力及入流量分布规律[J].中国石油大学学报:自然科学版,2014,38(1):92-97.
LI Mingzhong,CHEN Huijuan,ZHANG Xiansong,et al.Wellbore pressure and inflow rate distribution of multi-lateral horizontal well for coalbed methane[J].Journal of China University of Petroleum:Edition of Natural Science,2014,38(1):92-97.
[25] MOZAFFARI S,NIKOOKAR M,EHSANI M R,et al.Numerical modeling of steam injection in heavy oil reservoirs[J].Fuel,2013,112:185-192.

多点注汽水平井井筒出流规律数值模拟

Numerical simulation of the outflow performance for horizontal wells with multiple steam injection valves

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	杨立红, 朱超凡, 曾皓, 苏建政, 王益维, 武俊文, 陈旭东, 郭威. 油页岩自生热原位转化直井与水平井开发效果数值模拟——以鄂尔多斯盆地旬邑地区油页岩为例[J]. 石油学报, 2023, 44(8): 1333-1343.
[2]	高永海, 尹法领, 张党生, 孙小辉, 赵欣欣, 陈野, 孙宝江. 水合物储层水平井钻井井筒-储层耦合模型与井壁稳定性分析[J]. 石油学报, 2023, 44(7): 1151-1166.
[3]	鲜保安, 高德利, 徐凤银, 毕延森, 李贵川, 王京光, 张洋, 韩金良. 中国煤层气水平井钻完井技术研究进展[J]. 石油学报, 2023, 44(11): 1974-1992.
[4]	陈志明, Yu Wei, 石璐铭, 胡连博, 廖新维. 压裂水平井的多模式裂缝网络试井模型及参数评价——以吉木萨尔页岩油为例[J]. 石油学报, 2023, 44(10): 1706-1726.
[5]	李宁, 冯周, 武宏亮, 田瀚, 刘鹏, 刘英明, 刘忠华, 王克文, 徐彬森. 中国陆相页岩油测井评价技术方法新进展[J]. 石油学报, 2023, 44(1): 28-44.
[6]	唐雪平, 洪迪峰, 高文凯, 彭烈新, 杨宝斌. 七段制恒工具面角三维水平井轨道设计方法[J]. 石油学报, 2022, 43(9): 1315-1324.
[7]	史晓东, 孙灵辉, 战剑飞, 李斌会, 韩雪, 陆慧敏, 蒋成刚. 松辽盆地北部致密油水平井二氧化碳吞吐技术及其应用[J]. 石油学报, 2022, 43(7): 998-1006.
[8]	柳军, 杜智刚, 郭晓强, 殷腾, 俞海, 曹大勇. 水平井裸眼分段压裂完井管柱下入屈曲磨损预测模型及规律[J]. 石油学报, 2022, 43(11): 1632-1641.
[9]	胡松, 王敏, 刘伟男, 王兵. 页岩水平井声波时差各向异性校正方法及其应用[J]. 石油学报, 2022, 43(1): 58-66.
[10]	罗红文, 李海涛, 李颖, 汪凤, 向雨行, 蒋贝贝, 于皓. 低渗透气藏压裂水平井产出剖面与裂缝参数反演解释[J]. 石油学报, 2021, 42(7): 936-947.
[11]	郜益华, 张迎春, 杨宝泉, 李珂, 苑志旺, 康博韬, 张昕, 张旭, 陈国宁. 复杂断块油田跨断层水平井产能预测及分段长度优化方法——以西非A深水油田为例[J]. 石油学报, 2021, 42(7): 948-961.
[12]	李国欣, 吴志宇, 李桢, 陈强, 鲜成刚, 刘合. 陆相源内非常规石油甜点优选与水平井立体开发技术实践 ——以鄂尔多斯盆地延长组7段为例[J]. 石油学报, 2021, 42(6): 736-750.
[13]	张家强, 李士祥, 李宏伟, 周新平, 刘江艳, 郭睿良, 陈俊霖, 李树同. 鄂尔多斯盆地延长组7油层组湖盆远端重力流沉积与深水油气勘探——以城页水平井区长7₃小层为例[J]. 石油学报, 2021, 42(5): 570-587.
[14]	许林, 刘书杰, 许明标, 冯桓榰, 邢希金, 邓佳佳. 压差激活密封剂的微缺陷自适应修复行为及机理[J]. 石油学报, 2021, 42(5): 686-694.
[15]	张胜飞, 孙新革, 苟燕, 张忠义, 王红庄, 周晓义, 解阳波, 吕柏林. 流量控制器在SAGD技术中的应用现状及思考[J]. 石油学报, 2021, 42(10): 1395-1404.