水平井裸眼分段压裂完井管柱下入屈曲磨损预测模型及规律

doi:10.7623/syxb202211010

石油学报 ›› 2022, Vol. 43 ›› Issue (11): 1632-1641.DOI: 10.7623/syxb202211010

水平井裸眼分段压裂完井管柱下入屈曲磨损预测模型及规律

柳军^1,2, 杜智刚¹, 郭晓强¹, 殷腾³, 俞海⁴, 曹大勇³

1. 西南石油大学机电工程学院四川成都 610500;
2. 成都大学机械工程学院四川成都 610106;
3. 川南航天能源科技有限公司四川泸州 646604;
4. 大庆油田有限责任公司试油试采分公司黑龙江大庆 163412

收稿日期:2021-10-06 修回日期:2022-04-12 出版日期:2022-11-25 发布日期:2022-12-02
通讯作者: 柳军
作者简介:柳军,男,1980年5月生,2011年获重庆大学博士学位,现为西南石油大学机电工程学院研究员、博士生导师,主要从事管柱力学和机械系统动力学研究。Email:201031010081@swpu.edu.cn
基金资助:
国家自然科学基金项目(No.51875489,No.52105125)、中国博士后科学基金项目(2021TQ0273,2022M712643)、四川省自然科学基金项目(2022NSFSC1922)和四川省重点研发计划项目(2022YFQ0034)资助。

Prediction model and law of buckling wear of open hole staged featuring completion string in horizontal well

Liu Jun^1,2, Du Zhigang¹, Guo Xiaoqiang¹, Yin Teng³, Yu Hai⁴, Cao Dayong³

1. School of Mechanical and Electrical Engineering, Southwest Petroleum University, Sichuan Chengdu 610500, China;
2. School of Mechanical Engineering, Chengdu University, Sichuan Chengdu 610106, China;
3. Southern Sichuan Aerospace Energy Technology Co., Ltd., Sichuan Luzhou 646604, China;
4. Oil Testing and Production Branch, PetroChina Daqing Oilfield Limited Company, Heilongjiang Daqing 163412, China

Received:2021-10-06 Revised:2022-04-12 Online:2022-11-25 Published:2022-12-02

摘要/Abstract

摘要： 针对水平井裸眼分段压裂完井管柱下入屈曲磨损的问题,使用微元法确定管柱轴力及摩擦阻力,采用能量法计算管柱临界屈曲载荷,根据White和Dason的"磨损效率"模型,建立了全井段管柱定量摩擦磨损量预测模型。基于此,探究了压裂级数、分段间距、油管规格对管柱屈曲及磨损的影响规律。研究结果表明:1压裂级数的提高使管柱中和点上移,每提升10级压裂,中和点约上移13.5 m,而分段间距长度和油管规格提高使中和点下移;2管柱屈曲风险随压裂级数增大而增大,随油管规格和分段间距长度增加而减小,每提升1 m分段间距长度,管柱最大屈曲风险位置的安全系数约提高0.1;3压裂级数与分段间距对管柱全井段磨损量影响较小,而油管规格提高使得管柱全井段磨损深度减小,但磨损面更宽。

关键词: 裸眼完井管柱, 分段压裂, 磨损量预测, 屈曲, 水平井

Abstract: To solve the problem of buckling wear of open hole stagedfeaturing completion string in horizontal well, the axial force and frictional resistance of string was determined using the infinitesimal method, and the critical buckling load of string was calculated out using the energy method. Based on the wear efficiency model of White & Dason, a quantitative frictional wear prediction model was developed for the completion string. On this basis, the influence of fracture stage, segment spacing and pipe specification on the buckling and wear of string was investigated. The results show that:(1)the neutralization point of the string is shifted upward due to the upgrade of fracturing stages, and the neutralization point shifts upward by about 13.5 m for each 10-stagefracturing upgraded, while the neutralization point is shifted downward due to the increase of segment spacing length and the improvement of pipe specification; (2)the risk of string buckling increases with the upgrade of fracturing stages and decreases with the increase of segment spacing length and the improvement of pipe specification, and the safety factor of maximum buckling risk location increases about 0.1 for each 1 m of segment spacing length; (3)the influence of fracture stages and segment spacing on the wear amount of the whole pipe string is small, while the improvement of pipe specification decreases the wear depth of the whole pipe string, and widens the wear surface.

Key words: open hole completion string, segmented fracturing, wear amount prediction, buckling, horizontal well

中图分类号:

TE931

柳军, 杜智刚, 郭晓强, 殷腾, 俞海, 曹大勇. 水平井裸眼分段压裂完井管柱下入屈曲磨损预测模型及规律[J]. 石油学报, 2022, 43(11): 1632-1641.

Liu Jun, Du Zhigang, Guo Xiaoqiang, Yin Teng, Yu Hai, Cao Dayong. Prediction model and law of buckling wear of open hole staged featuring completion string in horizontal well[J]. Acta Petrolei Sinica, 2022, 43(11): 1632-1641.

参考文献

[1] 郑云川,陶建林,蒋玲玲,等. 苏里格气田裸眼水平井分段压裂工艺技术及其应用[J].天然气工业,2010,30(12):44-47.
ZHENG Yunchuan,TAO Jianlin,JIANG Lingling,et al.Application of open hole horizontal well multiple fracturing in the Sulige Gas Field[J].Natural Gas Industry,2010,30(12):44-47.
[2] 姜瑞忠,何吉祥,姜宇,等.页岩气藏压裂水平井Blasingame产量递减分析方法建立与应用[J].石油学报,2019,40(12):1503-1510.
JIANG Ruizhong,HE Jixiang,JIANG Yu,et al.Establishment and application of Blasingame production decline analysis method for fractured horizontal well in shale gas reservoirs[J].Acta Petrolei Sinica,2019,40(12):1503-1510.
[3] 王建军,于志强.水平井裸眼选择性分段压裂完井技术及工具[J].石油机械,2011,39(3):59-62.
WANG Jianjun,YU Zhiqiang.The completion technology and tool for open-hole preferential staged fracturing of the horizontal well[J].China Petroleum Machinery,2011,39(3):59-62.
[4] 蒲春生,郑恒,杨兆平,等.水平井分段体积压裂复杂裂缝形成机制研究现状与发展趋势[J].石油学报,2020,41(12):1734-1743.
PU Chunsheng,ZHENG Heng,YANG Zhaoping,et al.Research status and development trend of the formation mechanism of complex fractures by staged volume fracturing in horizontal wells[J].Acta Petrolei Sinica,2020,41(12):1734-1743.
[5] 丁昊明,戴彩丽,高静,等.国内外煤层气开发技术综述[J].煤,2013,22(4):24-26.
DING Haoming,DAI Caili,GAO J,et al.Overview of CBM development technology at home and abroad[J].Coal,2013,22(4):24-26.
[6] 聂海宽,汪虎,何治亮,等.常压页岩气形成机制、分布规律及勘探前景——以四川盆地及其周缘五峰组—龙马溪组为例[J].石油学报,2019,40(2):131-143.
NIE Haikuan,WANG Hu,HE Zhiliang,et al.Formation mechanism,distribution and exploration prospect of normal pressure shale gas reservoir:a case study of Wufeng Formation-Longmaxi Formation in Sichuan Basin and its periphery[J].Acta Petrolei Sinica,2019,40(2):131-143.
[7] 黄兴,李天太,王香增,等.致密砂岩储层可动流体分布特征及影响因素——以鄂尔多斯盆地姬塬油田延长组长8油层组为例[J].石油学报,2019,40(5):557-567.
HUANG Xing,LI Tiantai,WANG Xiangzeng,et al.Distribution characteristics and its influence factors of movable fluid in tight sandstone reservoir:a case study from Chang-8 oil layer of Yanchang Formation in Jiyuan oilfield,Ordos Basin[J].Acta Petrolei Sinica,2019,40(5):557-567.
[8] 张云鹏,杨生文,赵战江,等.临兴区块致密砂岩气藏裸眼水平井分段压裂技术[J].油气井测试,2021,30(2):61-66.
ZHANG Yunpeng,YANG Shengwen,ZHAO Zhanjiang,et al.Staged fracturing technology of open hole horizontal well in tight sandstone gas reservoir of Linxing block[J].Well Testing,2021,30(2):61-66.
[9] JOHANCSIK C A,FRIESEN D B,DAWSON R.Torque and drag in directional wells-prediction and measurement[J].Journal of Petroleum Technology,1984,36(6):987-992.
[10] 王艳红.水平井完井管柱可下入性分析研究[D].青岛:中国石油大学,2008.
WANG Yanhong.Study on the tripability of completion string in horizontal well[D].Qingdao:China University of Petroleum,2008.
[11] 于永南,韩志勇,路永明.弯曲井眼中柔性钻柱的屈曲问题[J].石油大学学报:自然科学版,1997,21(6):32-34.
YU Yongnan,HAN Zhiyong,LU Yongming.Buckling of flex-stem in curved well[J].Journal of China University of Petroleum:Natural Science Edition,1997,21(6):32-34.
[12] 署恒木.液压作用下套管柱临界屈曲载荷计算的能量法[J].力学与实践,2000,22(5):14-17.
SHU Hengmu.Caculation of critical buckling load for casing string subjected to liquid pressure by energy method[J].Mechanics in Engineering,2000,22(5):14-17.
[13] 练章华,牟易升,刘洋,等.高温高压超深气井油管柱屈曲行为研究[J].天然气工业,2018,38(1):89-94.
LIAN Zhanghua,MOU Yisheng,LIU Yang,et al.Buckling behaviors of tubing strings in HTHP ultra-deep wells[J].Natural Gas Industry,2018,38(1):89-94.
[14] 刘祥康,丁亮亮,李玉飞,等.超深气井完井管柱屈曲行为研究[J].石油机械,2020,48(2):29-34.
LIU Xiangkang,DING Liangliang,LI Yufei,et al.Study of the buckling behavior of completion strings for ultra-deep gas wells[J].China Petroleum Machinery,2020,48(2):29-34.
[15] 岳欠杯,刘巨保,付茂青.井筒内受压杆管后屈曲能量法分析与实验研究[J].力学与实践,2015,37(6):713-718.
YUE Qianbei,LIU Jubao,FU Maoqing.The energy method and experimental study of post-buckling of the pressurized rod string in wellbore[J].Mechanics in Engineering,2015,37(6):713-718.
[16] 温后珍,闫兵洋,曹梦雨,等.油管柱在套管中的屈曲行为试验研究[J].石油矿场机械,2017,46(3):36-40.
WEN Houzhen,YAN Bingyang,CAO Mengyu,et al.Experimental study of buckling behavior of tubing string in the casing[J].Oil Field Equipment,2017,46(3):36-40.
[17] WHITE J P,DAWSON R.Casing wear:laboratory measurements and field predictions[J].SPE Drilling & Completion,1987,2(1):56-62.
[18] 余磊,樊建春,张来斌,等.深井、超深井套管磨损机理及预测技术研究[J].润滑与密封,2004(5):87-90.
YU Lei,FAN Jianchun,ZHANG Laibin,et al.Recent advances in the research of casing wear mechanism and predicting methods in deep & ultra-deep well drilling engineering[J].Lubrication Engineering,2004(5):87-90.
[19] 窦益华,姜学海,张福祥.高密度钻井液润滑下套管磨损实验研究[J].润滑与密封,2007(9):26-28.
DOU Yihua,JIANG Xuehai,ZHANG Fuxiang.Experimental research on casing wear in drilling fluids of high density[J].Lubrication Engineering,2007(9):26-28.
[20] GAO Deli,SUN Lianzhong,LIAN Jihong.Prediction of casing wear in extended-reach drilling[J].Petroleum Science,2010,7(4): 494-501.
[21] 曹银萍,王小增,王新河,等.钻井液密度对高钢级套管磨损量的影响研究[J].石油机械,2013,41(8):5-8.
CAO Yinping,WANG Xiaozeng,WANG Xinhe,et al.Research on the effects of drilling fluid density on high grade steel casing abrasion[J].China Petroleum Machinery,2013,41(8):5-8.
[22] 曹银萍,王小增,马文海,等.硬度对套管耐磨性能影响的实验研究[J].润滑与密封,2014,39(8):48-52.
CAO Yinping,WANG Xiaozeng,MA Wenhai,et al.Experimental study of the influence of hardness on casing wear resistance[J].Lubrication Engineering,2014,39(8):48-52.
[23] 毛良杰,蔡明杰,田径,等.钻井液类型对套管磨损行为的影响[J].材料科学与工程学报,2020,38(3):482-487.
MAO Liangjie,CAI Mingjie,TIAN Jing,et al.Effect of drilling fluid type on wear behavior of casing[J].Journal of Materials Science and Engineering,2020,38(3):482-487.
[24] 陈江华,吴惠梅,李忠慧,等.超深定向井钻井中钻井参数对套管磨损量的影响[J].石油钻采工艺,2014,36(5):10-12.
CHEN Jianghua,WU Huimei,LI Zhonghui,et al.Effect of drilling parameters on casing wear rate in ultra-deep directional well drilling[J].Oil Drilling & Production Technology,2014,36(5):10-12.
[25] SUN Lianzhong,GAO Deli,ZHU Kuanliang.Models & tests of casing wear in drilling for oil & gas[J].Journal of Natural Gas Science and Engineering,2012,4:44-47.
[26] 李国亮,米红学,王小增,等.油基泥浆中P110套管磨损机理和耐磨性能[J].科学技术与工程,2015,15(2):83-87.
LI Guoliang,MI Hongxue,WANG Xiaozeng,et al.Wear resistance and mechanism of P110 casing in oil based muds[J].Science Technology and Engineering,2015,15(2):83-87.
[27] 梁尔国,李子丰,王金敏,等.油气井套管磨损规律试验研究[J].石油钻探技术,2015,43(1):69-74.
LIANG Erguo,LI Zifeng,WANG Jinmin,et al.Experimental study on casing wear mechanism in oil and gas wells[J].Petroleum Drilling Techniques,2015,43(1):69-74.
[28] 杨威.套管磨损预测与防磨减摩措施研究[D].成都:西南石油大学,2018.
YANG Wei.Study on casing wear prediction and measurement of anti-wear and friction reduction[D].Chengdu:Southwest Petroleum University,2018.
[29] 谭雷川,高德利,ADEEB S,等.基于钻柱正弦屈曲的套管磨损预测模型[J].中国石油大学学报:自然科学版,2019,43(4):69-74.
TAN Leichuan,GAO Deli,ADEEB S,et al.Casing wear prediction model in consideration of sinusoidal buckled drill string[J].Journal of China University of Petroleum:Edition of Natural Science,2019,43(4):69-74.
[30] 黄文君,张星坤,高德利,等.复合模式下套管磨损形状与深度计算模型[J].石油学报,2021,42(10):1373-1381.
HUANG Wenjun,ZHANG Xingkun,GAO Deli,et al.Casing wear shape and depth calculation model in a compound mode[J].Acta Petrolei Sinica,2021,42(10):1373-1381.
[31] GUO Xiaoqiang,LIU Jun,DAI Liming,et al.Safety evaluation method of tubing strings in high-pressure,high-temperature and high-yield gas wells based on FIV analysis[J].Engineering Failure Analysis,2021,120:105044.
[32] 陈康.钻柱屈曲特性模拟与分析[D].成都:西南石油大学,2015.
CHEN Kang.Simulation and analysis of buckling characteristics of drill string[D].Chengdu:Southwest Petroleum University,2015.
[33] SONG J S,BOWEN J,KLEMENTICH F.The internal pressure capacity of crescent-shaped wear casing[R].SPE 23902,1992.

水平井裸眼分段压裂完井管柱下入屈曲磨损预测模型及规律

Prediction model and law of buckling wear of open hole staged featuring completion string in horizontal well

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	李宁, 冯周, 武宏亮, 田瀚, 刘鹏, 刘英明, 刘忠华, 王克文, 徐彬森. 中国陆相页岩油测井评价技术方法新进展[J]. 石油学报, 2023, 44(1): 28-44.
[2]	唐雪平, 洪迪峰, 高文凯, 彭烈新, 杨宝斌. 七段制恒工具面角三维水平井轨道设计方法[J]. 石油学报, 2022, 43(9): 1315-1324.
[3]	史晓东, 孙灵辉, 战剑飞, 李斌会, 韩雪, 陆慧敏, 蒋成刚. 松辽盆地北部致密油水平井二氧化碳吞吐技术及其应用[J]. 石油学报, 2022, 43(7): 998-1006.
[4]	胡松, 王敏, 刘伟男, 王兵. 页岩水平井声波时差各向异性校正方法及其应用[J]. 石油学报, 2022, 43(1): 58-66.
[5]	罗红文, 李海涛, 李颖, 汪凤, 向雨行, 蒋贝贝, 于皓. 低渗透气藏压裂水平井产出剖面与裂缝参数反演解释[J]. 石油学报, 2021, 42(7): 936-947.
[6]	郜益华, 张迎春, 杨宝泉, 李珂, 苑志旺, 康博韬, 张昕, 张旭, 陈国宁. 复杂断块油田跨断层水平井产能预测及分段长度优化方法——以西非A深水油田为例[J]. 石油学报, 2021, 42(7): 948-961.
[7]	李国欣, 吴志宇, 李桢, 陈强, 鲜成刚, 刘合. 陆相源内非常规石油甜点优选与水平井立体开发技术实践 ——以鄂尔多斯盆地延长组7段为例[J]. 石油学报, 2021, 42(6): 736-750.
[8]	张家强, 李士祥, 李宏伟, 周新平, 刘江艳, 郭睿良, 陈俊霖, 李树同. 鄂尔多斯盆地延长组7油层组湖盆远端重力流沉积与深水油气勘探——以城页水平井区长7₃小层为例[J]. 石油学报, 2021, 42(5): 570-587.
[9]	张胜飞, 孙新革, 苟燕, 张忠义, 王红庄, 周晓义, 解阳波, 吕柏林. 流量控制器在SAGD技术中的应用现状及思考[J]. 石油学报, 2021, 42(10): 1395-1404.
[10]	刘合, 匡立春, 李国欣, 王峰, 金旭, 陶嘉平, 孟思炜. 中国陆相页岩油完井方式优选的思考与建议[J]. 石油学报, 2020, 41(4): 489-496.
[11]	林日亿, 李端, 王新伟, 杨正大, 张立强. 水平井配汽三维物理模拟实验[J]. 石油学报, 2020, 41(12): 1649-1656.
[12]	冯其红, 徐世乾, 任国通, 王森, 李昱垚. 致密油多级压裂水平井井网参数分级优化[J]. 石油学报, 2019, 40(7): 830-838.
[13]	樊建明, 王冲, 屈雪峰, 成良丙, 薛婷. 鄂尔多斯盆地致密油水平井注水吞吐开发实践——以延长组长7油层组为例[J]. 石油学报, 2019, 40(6): 706-715.
[14]	王志刚. 涪陵大型海相页岩气田成藏条件及高效勘探开发关键技术[J]. 石油学报, 2019, 40(3): 370-382.
[15]	姜瑞忠, 何吉祥, 姜宇, 范海军. 页岩气藏压裂水平井Blasingame产量递减分析方法建立与应用[J]. 石油学报, 2019, 40(12): 1503-1510.