双台肩钻杆接头三维力学分析

doi:10.7623/syxb201205019

石油学报 ›› 2012, Vol. 33 ›› Issue (5): 871-877.DOI: 10.7623/syxb201205019

双台肩钻杆接头三维力学分析

狄勤丰 1　陈　锋 1　王文昌 2　王明杰 2　赵域栋 1　袁鹏斌 3　周永其 3

1　上海大学上海市应用数学和力学研究所　上海　200072；2　上海市力学在能源工程中的应用重点实验室　上海　200072；3　上海石油管工程技术研究中心　上海　200949

收稿日期:2011-12-18 修回日期:2012-04-20 出版日期:2012-09-25 发布日期:2012-11-27
通讯作者: 狄勤丰
作者简介:狄勤丰，男，1963年8月生，1987年获华东石油学院硕士学位，1997年获西南石油大学博士学位，现为上海大学教授、博士生导师，2010年入选上海领军人才，主要从事石油工程力学方面的研究。
基金资助:
国家自然科学基金项目(No.51174130,No.50674065)、上海市重点学科建设项目(S30106)、上海市教委科研创新项目（11CXY32）和上海领军人才基金项目资助。

Three-dimensional mechanical analysis of the double-shouldered tool joint

DI Qinfeng 1　CHEN Feng 1　WANG Wenchang 2　WANG Mingjie 2　ZHAO Yudong 1　YUAN Pengbin 3　ZHOU Yongqi 3

Received:2011-12-18 Revised:2012-04-20 Online:2012-09-25 Published:2012-11-27

摘要/Abstract

摘要：

建立了双台肩钻杆接头的三维有限元模型，利用显式动力学有限元方法分析了双台肩钻杆接头在上扣扭矩、轴向拉力和弯矩作用下的力学特性。相比二维轴对称模型，三维有限元模型可以考虑螺纹的螺旋升角，有效地模拟螺纹接头的上扣特性。计算结果表明，上扣扭矩的作用使得接头在螺纹牙、主台肩、副台肩处产生一定的预紧力，从而实现公扣、母扣间的过盈配合；轴向拉力使得螺纹牙上的接触压力上升而主台肩、副台肩上的接触压力下降，这一方面加重了螺纹牙的负担，另一方面也影响了接头的密封性能；在弯矩的作用下，钻杆接头的应力分布呈现出明显的非对称特性。此外，在上扣扭矩和轴向拉力作用下，各螺纹牙的承载很不均匀，两端的几牙螺纹承担了大部分的载荷，而中间段螺纹牙仅承担了小部分载荷。

关键词: 螺纹接头, 三维有限元分析, 螺旋升角, 上扣扭矩, 弯矩

Abstract:

The present paper established a three-dimensional finite element model of the double-shouldered tool joint, and analyzed mechanical behaviors of the tool joint under make-up torque, axial tension and bending moment by means of the explicit dynamic finite element method. Compared with a two-dimensional axisymmetric model, the three-dimensional finite element model can effectively simulate the make-up behaviors of threaded connection by taking the helix ascending angle of screw thread into consideration. The results show that the make-up torque can produce a certain preload of the threaded connection on the mating surface of threaded teeth, primary shoulder and secondary shoulder, which implements the interference fit between male and female threads. Axial tension increases the contact pressure on threaded teeth but decreases that on the primary and secondary shoulders, which, on one hand, aggravates the load of threaded teeth, and on the other hand, affects the sealing performance of tool joint. The stress distribution of tool joint takes on a distinct asymmetric property under the bending moment. Besides, the load of individual threaded tooth is unevenly distributed under make-up torque and axial tension, the most load is sustained by several threaded teeth at the both ends of the tool joint, while intermediate threaded teeth sustain only a less load.

Key words: threaded connection, three-dimensional finite element analysis, helix ascending angle, make-up torque, bending moment

狄勤丰　陈　锋　王文昌　王明杰　赵域栋　袁鹏斌　周永其. 双台肩钻杆接头三维力学分析[J]. 石油学报, 2012, 33(5): 871-877.

DI Qinfeng　CHEN Feng　WANG Wenchang　WANG Mingjie　ZHAO Yudong. Three-dimensional mechanical analysis of the double-shouldered tool joint[J]. Editorial office of ACTA PETROLEI SINICA, 2012, 33(5): 871-877.

参考文献

[1]Assanelli A P,Xu Q,Benedetto F,et al.Numerical/experimental analysis of an API 8-round connection[J].Journal of Energy Resources Technology,1997,119(2):81-88.

[2]Bahai H.A parametric model for axial and bending stress concentration factors in API drillstring threaded connectors[J].International Journal of Pressure Vessels and Piping,2001,78(7):495-505.

[3]Baragetti S.Effects of taper variation on conical threaded connections load distribution[J].Journal of Mechanical Design, 2002,124(2):320-329.

[4]高连新,金烨.套管连接螺纹的受力分析与改善措施[J].上海交通大学学报,2004,38(10):1729-1732.

Gao Lianxin,Jin Ye.The load analysis and betterment of casing connection[J].Journal of Shanghai Jiaotong University, 2004,38(10):1729-1732.

[5]Yuan Guangjie,Yao Zhenqiang,Wang Qinghua,et al.Numerical and experimental distribution of temperature and stress fields in API round threaded connection[J].Engineering Failure Analysis,2006,13(8):1275-1284.

[6]石晓兵,施太和,王敬浩,等.下部钻柱组合的变形及应力研究[J].石油学报,2002,23(4):93-96.

Shi Xiaobing,Shi Taihe,Wang Jinghao,et al.Research on the deformation and stress of BHA[J].Acta Petrolei Sinica,2002,23(4):93-96.

[7]狄勤丰,朱卫平,姚建林,等.预弯曲动力学防斜打快钻具组合动力学模型[J].石油学报,2007,28(6):118-121.

Di Qinfeng,Zhu Weiping,Yao Jianlin,et al.Dynamic model of bottom hole assembly used in pre-bending dynamic vertical and fast drilling technology[J].Acta Petrolei Sinica,2007,28(6):118-121.

[8]祝效华,刘清友,童华.三维井眼全井钻柱系统动力学模型研究[J].石油学报,2008,29(2):288-291.

Zhu Xiaohua,Liu Qingyou,Tong Hua.Research on dynamics model of full hole drilling-string system with three-dimensional trajectory[J].Acta Petrolei Sinica,2008,29(2):288-291.

[9]庞东晓,刘清友,孟庆华,等.三维弯曲井眼钻柱接触非线性问题求解方法[J].石油学报,2009,30(1):121-124.

Pang Dongxiao,Liu Qingyou,Meng Qinghua,et al.Solving method for nonlinear contact problem of drill strings in 3D curved borehole[J].Acta Petrolei Sinica,2009,30(1):121-124.

[10]唐继平,狄勤丰,胡以宝,等.铝合金钻杆的动态特性及磨损机理分析[J].石油学报,2010,31(4):684-688.

Tang Jiping,Di Qinfeng,Hu Yibao,et al.Analysis on dynamic characteristics and wear mechanism of aluminum alloy drill pipe[J].Acta Petrolei Sinica,2010,31(4):684-688.

[11]Fukuoka T,Nomura M.Proposition of helical thread modeling with accurate geometry and finite element analysis[J].Journal of Pressure Vessel Technology,2008,130(1):011204-011206.

[12]Shahani A R,Sharifi S M H.Contact stress analysis and calculation of stress concentration factors at the tool joint of a drill pipe[J].Materials & Design,2009,30(9):3615-3621.

[13]刘巨保,丁宇奇,韩礼红.基于三维有限元模型的钻具连接螺纹上扣扭矩影响分析[J].石油矿场机械,2009,38(3):28-32.

Liu Jubao,Ding Yuqi,Han Lihong.Impact analysis of make-up torque of drill connecting thread based on 3-D finite element model[J].Oil Field Equipment,2009,38(3):28-32.

[14]庄茁，由小川，廖剑辉，等.基于ABAQUS的有限元分析和应用[M].北京：清华大学出版社,2009:191.

Zhuang Zhuo,You Xiaochuan,Liao Jianhui,et al.Finite element analysis and applications based on ABAQUS[M].Beijing: Tshinghua University Press,2009:191.

[15]石亦平，周玉蓉.ABAQUS有限元分析实例详解[M].北京：机械工业出版社,2011:169.

Shi Yiping,Zhou Yurong.The example of the finite element analysis in ABAQUS[M].Beijing:China Machine Press,2011:169.

双台肩钻杆接头三维力学分析

Three-dimensional mechanical analysis of the double-shouldered tool joint

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 8

编辑推荐

Metrics

本文评价

[1]	狄勤丰, 王楠, 陈锋, 陈涛, 王文昌, 陈薇. 磨损套管螺纹接头密封面力学特性[J]. 石油学报, 2021, 42(5): 669-676.
[2]	冯进, 魏俊, 刘倩倩, 马良丰. 七缸往复泵曲柄初相角布置方案及优选[J]. 石油学报, 2018, 39(3): 357-364.
[3]	狄勤丰, 陈锋, 李宁, 王明杰, 王文昌, 刘树林. 超深井钻具接头极限工作扭矩图版及其应用[J]. 石油学报, 2016, 37(4): 516-522.
[4]	洪迪峰, 唐雪平, 苏义脑, 盛利民, 窦修荣. 非连续性旋转导向钻具组合的广义纵横弯曲法[J]. 石油学报, 2014, 35(3): 543-550.
[5]	闫铁, 范森, 石德勤. 钻铤螺纹联接处载荷分布规律研究[J]. 石油学报, 1996, 17(3): 116-122.
[6]	黄惠泽, 白家祉. 定向井控制技术中套筒型钻井变向器的理论分析[J]. 石油学报, 1993, 14(1): 99-108.
[7]	赵华, 李中华, 匡震邦, 张毅, 李鹤林. 石油钻杆接头表面裂纹应力强度因子三维有限元分析Ⅰ.计算方法与模型[J]. 石油学报, 1992, 13(S1): 187-193.
[8]	赵华, 李中华, 匡震邦, 张毅, 李鹤林. 石油钻杆接头表面裂纹应力强度因子三维有限元分析Ⅱ.母螺纹齿根带半椭圆表面裂纹[J]. 石油学报, 1992, 13(S1): 191-202.