考虑稠油非牛顿性质的蒸汽吞吐产能预测模型

doi:10.7623/syxb201701009

石油学报 ›› 2017, Vol. 38 ›› Issue (1): 84-90.DOI: 10.7623/syxb201701009

考虑稠油非牛顿性质的蒸汽吞吐产能预测模型

杨戬^1,2, 李相方², 陈掌星^2,3, 田冀¹, 黄亮², 刘新光¹

1. 海洋石油高效开发国家重点实验室北京 102200;
2. 中国石油大学石油工程学院北京 102249;
3. 卡尔加里大学化学与石油工程学院加拿大卡尔加里 T2N1N4

收稿日期:2016-04-11 修回日期:2016-09-04 出版日期:2017-01-25 发布日期:2017-01-23
通讯作者: 李相方,男,1955年5月生,1982年获石油大学(华东)学士学位,1992年获石油大学(北京)博士学位,现为中国石油大学(北京)石油工程学院教授、博士生导师,主要从事非常规油气渗流及开发的研究工作。Email:lixf2013@vip.163.com
作者简介:杨戬,男,1989年3月生,2011年获中国石油大学(华东)石油工程专业学士学位,现为中国石油大学(北京)油气田开发工程专业博士研究生,主要从事油藏工程及渗流理论的研究。Email:yangjian315@126.com
基金资助:
海洋石油高效开发国家重点实验室开放基金项目（2015-YXKJ-001）资助。

A productivity prediction model for cyclic steam stimulation in consideration of non-Newtonian characteristics of heavy oil

Yang Jian^1,2, Li Xiangfang², Chen Zhangxing^2,3, Tian Ji¹, Huang Liang², Liu Xinguang¹

1. State Key Laboratory of Offshore Oil Exploitation, Beijing 102200, China;
2. School of Petroleum Engineering, China University of Petroleum, Beijing 102249, China;
3. Institute of Chemical and Petroleum Engineering, University of Calgary, Calgary T2N1N4, Canada

Received:2016-04-11 Revised:2016-09-04 Online:2017-01-25 Published:2017-01-23

摘要/Abstract

摘要：

与常规油不同，当达到某特定温度时，稠油呈现牛顿流体状态，而在该温度值以下时，稠油呈现非牛顿流体状态，即存在启动压力梯度。经典的解析模型将蒸汽吞吐分为热区与冷区2个部分，热区温度为蒸汽温度，冷区温度为原始地层温度。然而在实际过程中，热区到冷区的温度是一个非等温的渐变过程，不会存在热区与冷区的边界处的突变现象。而且在生产过程中，稠油在不同区域呈现牛顿流体与非牛顿流体2种状态，不同区域的稠油渗流方程不同。针对这种情况，基于Marx-Langenheim方程，对蒸汽吞吐的解析模型进行了改进。在注入阶段，考虑了热区非等温分布的特征；在生产阶段，考虑了稠油牛顿流体区与非牛顿流体区的渗流耦合。模型应用结果表明，该模型更加接近实际生产情况，有较好的应用价值。

关键词: 蒸汽吞吐, 非牛顿性质, 启动压力梯度, 产能预测, 耦合渗流

Abstract:

Unlike conventional oil, heavy oil exhibits Newtonian fluid state when it reaches a specified temperature. Specifically, heavy oil shows non-Newtonian fluid state at a temperature below the specified value, i.e., a threshold pressure gradient occurs. In a classical analytical model, the reservoir for cyclic steam stimulation is divided into hot zone and cold zone; the temperature of hot zone is steam temperature while that of cold zone is initial formation temperature. However, in practice, temperature transition from hot zone to cold zone is a non-isothermal gradual change process, and no abrupt change will occur at the boundary between hot zone and cold zone. Moreover, during production, heavy oil presents two states in different zones, i.e., Newtonian fluid and non-Newtonian fluid; correspondingly, heavy oil flow equations are also different. In light of the two points above, the analytical model of cyclic steam stimulation was modified on the basis of Marx-Langenheim equations. Considerations included non-isothermal distribution characteristics of hot zone during injection stage and flow coupling of heavy oil in Newtonian fluid zone and non-Newtonian fluid zone during production stage. The results of the model application shows that this model is more close to actual production situation and has better applicability.

Key words: cyclic steam stimulation, non-Newtonian characteristics, threshold pressure gradient, productivity prediction, coupled flow

中图分类号:

TE357.4

杨戬, 李相方, 陈掌星, 田冀, 黄亮, 刘新光. 考虑稠油非牛顿性质的蒸汽吞吐产能预测模型[J]. 石油学报, 2017, 38(1): 84-90.

Yang Jian, Li Xiangfang, Chen Zhangxing, Tian Ji, Huang Liang, Liu Xinguang. A productivity prediction model for cyclic steam stimulation in consideration of non-Newtonian characteristics of heavy oil[J]. Acta Petrolei Sinica, 2017, 38(1): 84-90.

参考文献

[1] FAROUQ Ali S M,JONES J A,MELDAU R F. Practical heavy oil recovery[M].Calgary:University of Calgary Press,1997.
[2] BOBERG T C.Thermal methods of oil recovery[M].New York:John Wiley & Sons,Inc,1988.
[3] XU Wenjiang,CHEN Zhangxing,SHAN Jincheng,et al.Studies and pilot project on steam stimulation with multiple fluids for offshore heavy oil reservoirs[R].SPE 165383,2013.
[4] 杜殿发,姚军,刘立支.边水稠油油藏水驱后蒸汽吞吐方案设计[J].石油大学学报:自然科学版,2000,24(2):44-46.
DU Dianfa,YAO Jun,LIU Lizhi.Program of steam soak for heavy oil reservoir after water flooding[J].Journal of the University of Petroleum,China:Edition of Natural Science,2000,24(2):44-46.
[5] 陈月明.注蒸汽热力采油[M].东营:石油大学出版社,2006:86-125.
CHEN Yueming.Thermal recovery method by steam injection[M].Dongying:China University of Petroleum Press, 2006:86-125.
[6] 吴正彬,庞占喜,刘慧卿,等.稠油油藏高温凝胶改善蒸汽驱开发效果可视化实验[J].石油学报,2015,36(11):1421-1426.
WU Zhengbin,PANG Zhanxi,LIU Huiqing,et al.A visible experiment on adoption of high-temperature gel for improving the development effect of steam flooding in heavy oil reservoirs[J].Acta Petrolei Sinica,2015,36(11):1421-1426.
[7] 江航,许强辉,马德胜,等.注空气开采过程中稠油结焦量影响因素[J].石油学报,2016,37(8):1030-1036.
JIANG Hang,XU Qianghui,MA Desheng,et al.Influence factors of coking amount during recovery of heavy oil by air injection[J].Acta Petrolei Sinica,2016,37(8):1030-1036.
[8] 李萍,刘志龙,邹剑,等.渤海旅大27-2油田蒸汽吞吐先导试验注采工程[J].石油学报,2016,37(2):242-247.
LI Ping,LIU Zhilong,ZOU Jian,et al.Injection and production project of pilot test on steam huff-puff in oilfield LD27-2,Bohai Sea[J].Acta Petrolei Sinica,2016,37(2):242-247.
[9] 曹嫣镔,刘冬青,王善堂,等.中深层稠油油藏化学辅助蒸汽驱三维物理模拟与应用[J].石油学报,2014,35(4):739-744.
CAO Yanbin,LIU Dongqing,WANG Shantang,et al.Three-dimensional physical simulation and application of chemistry assistant steam flooding on middle and deep heavy oil reservoir[J].Acta Petrolei Sinica,2014,35(4):739-744.
[10] HOU Jian,ZHOU Kang,ZHAO Hui,et al.Hybrid optimization technique for cyclic steam stimulation by horizontal wells in heavy oil reservoir[J].Computers and Chemical Engineering,2016,84:363-370.
[11] ZHANG Chao,LI Zhaomin,WANG Houyu,et al.Performance of flue gas and foam assisted steam huff and puff with horizontal well in enhanced recovery of Fengcheng oil field[R].SPE 170105,2014.
[12] AN Jiuquan,JI Li,HUA Jiang.Steam-flood trial and research on mid-deep heavy oil reservoir Qi40 Block in Liaohe oilfield[R].SPE 104403,2006.
[13] 张兆祥,刘慧卿,杨阳,等.稠油油藏蒸汽驱评价新方法[J].石油学报,2014,35(4):733-738.
ZHANG Zhaoxiang,LIU Huiqing,YANG Yang,et al.A new evaluation method of steam flooding for heavy oil reservoirs[J].Acta Petrolei Sinica,2014,35(4):733-738.
[14] MARX J W,LANGENHEIM R H.Reservoir heating by hot fluid injection[R].SPE 1266,1959.
[15] WILLMAN B T,VALLEROY V V,RUNBERG G W,et al.Laboratory studies of oil recovery by steam injection[J].Journal of Petroleum Technology,1961,13(7):681-690.
[16] MANDL G,VOLEK C W.Heat and mass transport in steam-drive processes[J].Society of Petroleum Engineers Journal,1969,9(1):59-79.
[17] DOU Hong'en,CHANG Yuwen,YU Jun,et al.A new mathematics model and theory for heavy-oil reservoir heating by huff ‘n’ puff[R].SPE 106234,2007.
[18] 李春兰,杨炳秀.稠油蒸汽吞吐开采非等温渗流产量预测模型[J].石油钻采工艺,2003,25(5):89-90.
LI Chunlan,YANG Bingxiu.Production model for cyclic steam stimulation in heavy oil reservoir considering non-isothermal flow[J].Oil Drilling & Production Technology,2003,25(5):89-90.
[19] 李春兰,程林松.稠油蒸汽吞吐加热半径动态计算方法[J].新疆石油地质,1998,19(3):247-249.
LI Chunlan,CHENG Linsong.A model for calculation heating radius in steam stimulation of viscous reservoir[J].Xinjiang Petroleum Geology,1998,19(3):247-249.
[20] 郑舰,陈更新,刘鹏程.一种新型蒸汽吞吐产能预测解析模型[J].石油天然气学报,2011,33(5):111-114.
ZHENG Jian,CHEN Gengxin,LIU Pengcheng.A new analytical model for productivity prediction in steam soak[J].Journal of Oil and Gas Technology,2011,33(5):111-114.
[21] 何聪鸽,穆龙新,许安著,等.稠油油藏蒸汽吞吐加热半径及产能预测新模型[J].石油学报,2015,36(12):1564-1570.
HE Congge,MU Longxin,XU Anzhu,et al.A new model of steam soaking heating radius and productivity prediction for heavy oil reservoirs[J].Acta Petrolei Sinica, 2015,36(12):1564-1570.
[22] WU Yushu.Theoretical studies of non-Newtonian and Newtonian fluid flow through porous media[D].Berkeley,California:University of California,1990.
[23] WANG Shaojun,HUANG Yanzhang,CIVAN F.Experimental and theoretical investigation of the Zaoyuan field heavy oil flow through porous media[J].Journal of Petroleum Science and Engineering,2006,50(2):83-101.
[24] PRADA A,CIVAN F.Modification of Darcy's law for the threshold pressure gradient[J].Journal of Petroleum Science and Engineering,1999,22(4):237-240.
[25] DONG Xiaohu,LIU Huiqing,WANG Qing,et al.Non-Newtonian flow characterization of heavy crude oil in porous media[J].Journal of Petroleum Exploration and Production Technology,2013,3(1):43-53.
[26] LIU H,WANG J,XIE Y,et al.Flow characteristics of heavy oil through porous media[J].Energy Sources,Part A:Recovery,Utilization,and Environmental Effects, 2011,34(4):347-359.
[27] SOCHI T.Pore-scale modeling of Non-Newtonian flow in porous media[D].London:Imperial College London,2007.
[28] 许家峰.考虑启动压力梯度普通稠油渗流规律研究[D].北京:中国石油大学,2007.
XU Jiafeng.The seepage law of ordinary heavy oil considering of TPG[D].Beijing:China University of Petroleum,2007.
[29] 许家峰,程林松,李春兰,等.普通稠油油藏启动压力梯度求解方法与应用[J].特种油气藏,2006,13(4):53-57.
XU Jiafeng,CHENG Linsong,LI Chunlan,et al.Starting pressure gradient calculation and its application in conventional heavy oil reservoir[J].Special Oil and Gas Reservoir,2006,13(4):53-57.
[30] 蒋明,许震芳.齐40块稠油流变特性实验研究[J].断块油气田,1997,4(6):19-22.
JIANG Ming,XU Zhenfang.Experimental study on rheologic properties of heavy oil for Block Qi-40[J].Fault-Block Oil & Gas Field,1997,4(6):19-22.
[31] 张金亮,王为民,申龙涉,等.辽河油田超稠油流变特性的试验研究[J].油气田地面工程,2006,25(7):11.
ZHANG Jinliang,WANG Weimin,SHEN Longshe,et al.Experimental study on rheologic properties of heavy oil in Liaohe oil field[J].Oil-Gasfield Surface Engineering,2006,25(7):11.
[32] 张凯,李阳,王琳娜,等.稠油流变特性实验研究[J].油气地质与采收率,2007,14(5):91-94.
ZHANG Kai,LI Yang,WANG Linna,et al.Experimental study on rheological characteristics of heavy oil[J].Petroleum Geology and Recovery Efficiency,2007,14(5):91-94.

考虑稠油非牛顿性质的蒸汽吞吐产能预测模型

A productivity prediction model for cyclic steam stimulation in consideration of non-Newtonian characteristics of heavy oil

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	崔传智, 孙莲婷, 单高军, 杨勇, 吴义志. 多层合采油井的多措施同步优化方法[J]. 石油学报, 2023, 44(8): 1356-1364,1381.
[2]	金国文, 王堂宇, 刘忠华, 谢然红, 邵亮, 李博宇. 基于核磁共振测井的砂砾岩储层分类与产能预测方法[J]. 石油学报, 2022, 43(5): 648-657.
[3]	郜益华, 张迎春, 杨宝泉, 李珂, 苑志旺, 康博韬, 张昕, 张旭, 陈国宁. 复杂断块油田跨断层水平井产能预测及分段长度优化方法——以西非A深水油田为例[J]. 石油学报, 2021, 42(7): 948-961.
[4]	李晓光. 辽河坳陷欢喜岭油田稠油成藏条件及勘探开发关键技术[J]. 石油学报, 2021, 42(4): 541-560.
[5]	王杰祥, 刘晓, 牛成成, 吴建平, 白祥维. 稠油油藏蒸汽吞吐防砂完井产能评价新方法[J]. 石油学报, 2020, 41(1): 80-87.
[6]	林加恩, 何辉, 韩章英. 未出现径向流的试井典型曲线及其分析方法[J]. 石油学报, 2017, 38(5): 562-569.
[7]	周明顺, 范宜仁, 刘志杰, 吴剑锋, 李辉, 宋岩, 高衍武. 饶阳凹陷复杂砂岩储层产能测井预测方法[J]. 石油学报, 2017, 38(2): 208-216.
[8]	黄志龙, 马剑, 梁世君, 梁浩, 陈旋, 康积伦. 源-储分离型凝灰岩致密油藏形成机理与成藏模式[J]. 石油学报, 2016, 37(8): 975-985.
[9]	李萍, 刘志龙, 邹剑, 刘海英, 于继飞, 范永涛. 渤海旅大27-2油田蒸汽吞吐先导试验注采工程[J]. 石油学报, 2016, 37(2): 242-247.
[10]	何聪鸽, 穆龙新, 许安著, 方思冬. 稠油油藏蒸汽吞吐加热半径及产能预测新模型[J]. 石油学报, 2015, 36(12): 1564-1570.
[11]	窦宏恩. 讨论《启动压力梯度真的存在吗？》一文[J]. 石油学报, 2013, 34(2): 412-416.
[12]	王晓冬　郝明强　韩永新 . 启动压力梯度的含义与应用[J]. 石油学报, 2013, 34(1): 188-191.
[13]	姜瑞忠　李林凯　徐建春　杨仁锋　庄　煜. 低渗透油藏非线性渗流新模型及试井分析[J]. 石油学报, 2012, 33(2): 264-268.
[14]	郝明强;胡永乐;李凡华. 特低渗透油藏压裂水平井产量递减规律[J]. 石油学报, 2012, 33(2): 269-273.
[15]	陈元千. 线性流的启动压力梯度不能用于平面径向流方程[J]. 石油学报, 2011, 32(6): 1088-1092.