液相放电等离子体破岩室内实验与破岩机理

doi:10.7623/syxb202005010

石油学报 ›› 2020, Vol. 41 ›› Issue (5): 615-628.DOI: 10.7623/syxb202005010

液相放电等离子体破岩室内实验与破岩机理

张辉¹, 蔡志翔¹, 陈安明², 刘科柔¹, 杨茂林¹, 余庆¹, 王昊¹, 谭天一¹, 陈雨飞¹

1. 中国石油大学(北京)石油工程学院北京 102249;
2. 中国石油化工集团华东石油工程有限公司江苏南京 210000

收稿日期:2019-06-17 修回日期:2020-02-21 出版日期:2020-05-25 发布日期:2020-06-08
通讯作者: 张辉,女,1971年5月生,1994年获石油大学(华东)学士学位,2006年获中国石油大学(北京)博士学位,现为中国石油大学(北京)石油工程学院教授、博士生导师,主要从事液相放电等离子体钻井破岩技术以及复杂结构井优化设计与控制技术研究。
作者简介:张辉,女,1971年5月生,1994年获石油大学(华东)学士学位,2006年获中国石油大学(北京)博士学位,现为中国石油大学(北京)石油工程学院教授、博士生导师,主要从事液相放电等离子体钻井破岩技术以及复杂结构井优化设计与控制技术研究。Email:zhanghui3702@163.com
基金资助:
国家自然科学基金面上项目（No.51774304）和国家科技重大专项（2017ZX05009-003）资助。

Experiments and mechanism of rock breaking by the plasma shock wave generated by underwater discharge

Zhang Hui¹, Cai Zhixiang¹, Chen Anming², Liu Kerou¹, Yang Maolin¹, Yu Qing¹, Wang Hao¹, Tan Tianyi¹, Chen Yufei¹

1. College of Petroleum Engineering, China University of Petroleum, Beijing 102249, China;
2. Sinopec Huadong Oilfield Service Corporation, Jiangsu Nanjing 210000, China

Received:2019-06-17 Revised:2020-02-21 Online:2020-05-25 Published:2020-06-08

摘要/Abstract

摘要：

液相放电等离子体破岩是一种将电能转换为冲击波机械能的新型高效破岩技术，目前国内外对其在石油钻井中的应用研究较少。开展了液相放电等离子体破岩室内实验：首先使用3组不同厚度的页岩验证了等离子体冲击波破岩的可行性；然后使用损伤变量和声幅衰减系数作为岩样损伤表征量，定量分析了不同影响因素下，混凝土岩样受等离子体冲击波作用后的损伤程度；使用3种岩样（混凝土、页岩、砂岩），验证了该技术对不同抗压强度岩样，在不同地层中的适应性；最后借助CT扫描，观察冲击波作用前后的岩样，分析和揭示了冲击波作用下岩样的损伤破坏形态和机制。室内实验结果表明：冲击波峰值压力高达130~190 MPa；页岩被劈裂成多块，混凝土岩样的破坏深度为3~5 mm，破坏程度随放电电压和冲击次数的增加而增加；载荷相同时，岩样的破坏程度随抗压强度减小而增加，但页岩的层理结构有利于吸收冲击波能量，增加其破坏程度；岩样的破坏形式以径向裂纹、片落裂纹和冲蚀坑为主。液相放电等离子体破岩机理的研究结果表明：冲击波作用岩样，岩样表面受压被破坏，岩样内部产生切向拉伸应力，应力波从岩样内部往边界传播时，在岩-液界面反射并产生拉伸应力，当拉伸应力大于岩样抗拉强度时产生裂纹；冲击波的产生伴随着高速射流，射流的水楔作用加速裂纹的扩展，形成冲蚀坑。

关键词: 等离子体, 液电效应, 破岩机理, 钻井提速, 室内实验

Abstract:

Plasma shock wave is a novel and efficient rock breaking technology that converts electrical energy into the mechanical energy of shock wave. At present, its application research in oil drilling is not sufficient.We conducted experiments of rock breaking by plasma shock wave:First, the feasibility of plasma shock wave rock breaking technology was verified by using 3 sets of shale samples with different thicknesses; and then the damage variable and attenuation coefficient were used to quantitatively analyze the damage degree of concrete rock samples after being impacted by plasma shock waves under different influencing factors; the use of three types of rock samples (concrete, shale, sandstone)has verified the adaptability of the technology to different compressive strength rock samples in different formations. Finally, CT scans were used to observe the internal damage of rock samples before and after the shock wave, and the rock-breaking patterns and mechanism of the shock wave were analyzed.The experimental results showed that the peak pressure of the shock wave was as high as 130~190 MPa; the shale samples were split into multiple pieces, and the damage depth of the concrete rock sample was 3~5 mm. The damage degree increased with the increase of the discharge voltage and the number of impacts; the damage degree of rock samples increased with the decrease of compressive strength under the same shock load, but the bedding structure of shale was beneficial for absorbing shock wave energy and increasing the damage degree. The main failure modes of rock samples were radial cracks, chipping cracks and erosion pits. Further analysis on the mechanism of rock breaking by plasma shock wave showed that the surface of rock samples was damaged by compression due to the shock waves, and tangential tensile stress was generated inside the rock samples. When the stress wave propagated from the inside to the boundary, it was reflected on the rock-liquid interface and generated tensile stress; when the tensile stress was greater than the tensile strength of rock samples, cracks were generated. The generation of shock waves was accompanied by high-speed jets. The propagation of cracks was accelerated by the water wedge effect of the jets.

Key words: plasma, electrohydraulic effect, mechanism of rock breaking, increase of drilling speed, laboratory experiment

中图分类号:

TE21

张辉, 蔡志翔, 陈安明, 刘科柔, 杨茂林, 余庆, 王昊, 谭天一, 陈雨飞. 液相放电等离子体破岩室内实验与破岩机理[J]. 石油学报, 2020, 41(5): 615-628.

Zhang Hui, Cai Zhixiang, Chen Anming, Liu Kerou, Yang Maolin, Yu Qing, Wang Hao, Tan Tianyi, Chen Yufei. Experiments and mechanism of rock breaking by the plasma shock wave generated by underwater discharge[J]. Acta Petrolei Sinica, 2020, 41(5): 615-628.

参考文献

[1] Tibbitts G A,Galloway G G.Particle drilling alters standard rock-cutting approach:Drilling/Completions[J].World Oil,2008,229(6):37-44.
[2] 侯绪田,赵小祥,赵向阳,等.巴西BM-C-33区块深水优快钻井技术研究与应用[J].钻采工艺,2018,41(2):33-36.
HOU Xutian,ZHAO Xiaoxiang,ZHAO Xiangyang,et al.Deepwater fast drilling technology used at Bm-C-33 block in Brazil[J].Drilling & Production Technology,2018,41(2):33-36.
[3] 沙林秀.钻井参数优化技术的研究现状与发展趋势[J].石油机械,2016,44(2):29-33.
SHA Linxiu.Drilling parameters optimization technology status and development trend[J].China Petroleum Machinery,2016,44(2):29-33.
[4] 邱自学,王璐璐,徐永和,等.页岩气钻井螺杆钻具的研究现状及发展趋势[J].钻采工艺,2019,42(2):36-37.
QIU Zixue,WANG Lulu,XU Yonghe,et al.Status quo and development trend of positive displacement motor used in shale gas drilling[J].Drilling & Production Technology,2019,42(2):36-37.
[5] 闫家,王稳石,张恒春,等.松科2井带涡轮钻具取心钻进探索[J].钻采工艺,2019,42(1):31-34.
YAN Jia,WANG Wenshi,ZHANG Hengchun,et al.Practice of turbo-drill core drilling in well SK-2[J].Drilling & Production Technology,2019,42(1):31-34.
[6] 韩烈祥,姚建林,李伟成.川渝地区须家河地层涡轮钻具配套孕镶金刚石钻头钻井提速技术[J].钻采工艺,2018,41(3):1-4.
HAN Liexiang,YAO Jianlin,LI Weicheng.Turbodrills combined with pdc bits to improve rop of drilling through Xujiahe at Sichuan-Chongqing area[J].Drilling & Production Technology,2018,41(3):1-4.
[7] 祝效华,刘伟吉.旋冲钻井技术的破岩及提速机理[J].石油学报,2018,39(2):216-222.
ZHU Xiaohua,LIU Weiji.Rock breaking and ROP rising mechanism of rotary-percussive drilling technology[J].Acta Petrolei Sinica,2018,39(2):216-222.
[8] 光新军,王敏生,皮光林.超高压水射流钻井技术现状及发展建议[J].钻采工艺,2017,40(1):37-40.
GUANG Xinjun,WANG Minsheng,PI Guanglin.Status and development suggestion for high-pressure water jet drilling[J].Drilling & Production Technology,2017,40(1):37-40.
[9] 秦春,陈小元,李禹,等.水力脉冲射流钻井提速技术在江苏油田的应用[J].石油机械,2015,43(5):17-21.
QIN Chun,CHEN Xiaoyuan,LI Yu,et al.Applications of hydraulic pulse jet technology in Jiangsu oilfield[J].China Petroleum Machinery,2015,43(5):17-21.
[10] 贺振国,李根生,王海柱,等.超临界二氧化碳射流中的颗粒跟随及影响因素[J].石油学报,2017,38(4):475-484.
HE Zhenguo,LI Gensheng,WANG Haizhu,et al.Particle following motion in supercritical carbon dioxide jet and its influence factors[J].Acta Petrolei Sinica,2017,38(4):475-484.
[11] 宋先知,吕泽昊,崔柳,等.高温射流反应腔结构设计与反应规律[J].石油学报,2017,38(5):587-596.
SONG Xianzhi,LV Zehao,CUI Liu,et al.Structure design and reaction law of high-temperature jet reaction chamber[J].Acta Petrolei Sinica,2017,38(5):587-596.
[12] 程晓泽,任福深,方天成,等.粒子射流耦合冲击破岩实验[J].石油学报,2018,39(2):232-239.
CHENG Xiaoze,REN Fushen,FANG Tiancheng,et al.Experiment of rock breaking by particle-jet coupling impact[J].Acta Petrolei Sinica,2018,39(2):232-239.
[13] 迟焕鹏,单衍胜,李奎,等.水力喷射微小井眼水平井流动耦合模型及影响规律[J].石油学报,2018,39(8):947-954.
CHI Huanpeng,SHAN Yansheng,LI Kui,et al.Coupled flow model and influence rule of hydra-jet micro-hole horizontal well[J].Acta Petrolei Sinica,2018,39(8):947-954.
[14] 汪海阁,葛云华,石林.深井超深井钻完井技术现状、挑战和"十三五"发展方向[J].天然气工业,2017,37(4):1-8.
WANG Haige,GE Yunhua,SHI Lin.Technologies in deep and ultra-deep well drilling:present status,challenges and future trend in the 13th five-year plan period (2016-2020)[J].Natural Gas Industry,2017,37(4):1-8.
[15] JAMALI S,WITTIG V,BÖRNER J,et al.Application of high powered Laser Technology to alter hard rock properties towards lower strength materials for more efficient drilling,mining,and Geothermal Energy production[J].Geomechanics for Energy and the Environment,2019,20:100112.
[16] KOCIS I,KRISTOFIC T,GAJDOS M,et al.Utilization of electrical plasma for hard rock drilling and casing milling[R].SPE 173016,2015.
[17] Cemhan S,Kelly G,Schmitt J.The Effect of Microwave Irradiation on Hard Rock as Pre-Treatment to Increase the Efficiency of Underground Mining[C]//CERC.2019:397-406.
[18] SONG Xianzhi,LYU Zehao,CUI Liu,et al.Comparison of numerical analysis on the downhole flow field for multi-orifice hydrothermal jet drilling technology for geothermal wells[J].Geothermics,2017,70:314-323.
[19] LYU Zehao,SONG Xianzhi,LI Gensheng,et al.Analysis of temperature simulation in downhole reaction chamber of hydrothermal jet drilling[J].International Journal of Heat and Mass Transfer,2018,123:342-353.
[20] 尤特金.液电效应[M].于家珊,译.北京:科学出版社,1962.
TKIN L A U.Electrohydraulic effect[M].YU Jiashan,trans.Beijing:Science Press,1962.
[21] 秦曾衍,左公宁,王永荣,等.高压强脉冲放电及其应用[M].北京:北京工业大学出版社,2000.
QIN Cengyan,ZUO Gongning,WANG Yongrong,et al.High voltage intense pulse discharge and its application[M].Beijing:Beijing University of Technology Press,2000.
[22] 王一博.水中等离子体声源的理论与实验研究[D].长沙:国防科学技术大学,2012.
WANG Yibo.Theoretical and experimental study of the underwater plasma acoustic source[D].Changsha:National University of Defense Technology,2012.
[23] YANG Chen.Mechanisms of stone fragmentation produced by Nano Pulse Lithotripsy (NPL)[D].Durham:Duke University,2017.
[24] EUBANK P T,PATEL M R,BARRUFET M A,et al.Theoretical models of the electrical discharge machining process.III.The variable mass,cylindrical plasma model[J].Journal of Applied Physics,1993,73(11):7900-7909.
[25] 楼志文.损伤力学基础[M].西安:西安交通大学出版社,1991.
LOU Zhiwen.Foundation of damage mechanics[M].Xi'an:Xi'an Jiaotong University Press,1991.
[26] TOUYA G,REESS T,PÉCASTAING L,et al.Development of subsonic electrical discharges in water and measurements of the associated pressure waves[J].Journal of Physics D:Applied Physics,2006,39(24):5236-5244.
[27] XI Xufeng,ZHONG Pei.Dynamic photoelastic study of the transient stress field in solids during shock wave lithotripsy[J].The Journal of the Acoustical Society of America,2001,109(3):1226-1239.
[28] MIHRADI S,HOMMA H,KANTO Y.Numerical analysis of kidney stone fragmentation by short pulse impingement:effect of geometry[J].Key Engineering Materials,2006,306-308:1283-1288.
[29] CAO Shunxiang,ZHANG Ying,LIAO Defei,et al.Shock-induced damage and dynamic fracture in cylindrical bodies submerged in liquid[J]. International Journal of Solids and Structures,2019,169:55-71.
[30] 潘井澜.爆破破岩机理的探讨[J].爆破,1994(4):1-6.
PAN Jinglan.Discussion on mechanism of rock breaking by blasting[J].Blasting,1994(4):1-6.
[31] 蒋金宝.爆炸激波对水泥试样损伤规律研究[D].青岛:中国石油大学(华东),2008.
JIANG Jinbao.Study on rule of cement sample damage by blast wave[D].Qingdao:China University of Petroleum,2008.
[32] 田守嶒,刘庆岭,盛茂,等.超临界CO₂直旋混合射流冲蚀岩石的损伤破坏机制[J].中国科学:物理学力学天文学,2017,47(11):114608.
TIAN Shouceng,LIU Qingling,SHENG Mao,et al.Mechanisms of rock breaking by swirling-round SC-CO₂ jet[J].Scientia Sinica Physica,Mechanica & Astronomica,2017,47(11):114608.
[33] CLEVELAND R O,SAPOZHNIKOV O A.Modeling elastic wave propagation in kidney stones with application to shock wave lithotripsy[J]. The Journal of the Acoustical Society of America,2005,118(4):2667-2676.

液相放电等离子体破岩室内实验与破岩机理

Experiments and mechanism of rock breaking by the plasma shock wave generated by underwater discharge

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 12

编辑推荐

Metrics

本文评价

[1]	刘伟吉, 张有建, 罗云旭, 祝效华. 岩石内部高压电脉冲等离子体通道生成机理[J]. 石油学报, 2023, 44(4): 684-697.
[2]	鹿腾, 班晓春, 李兆敏, 高永荣, 郭二鹏, 杨建平, 马宏斌, 王宏远, 魏耀. 烟道气辅助SAGD蒸汽腔扩展机理[J]. 石油学报, 2021, 42(8): 1072-1080.
[3]	祝效华, 罗云旭, 刘伟吉, 高锐, 贾玉丹, 刘呈君. 等离子体电脉冲钻井破岩机理的电击穿实验与数值模拟方法[J]. 石油学报, 2020, 41(9): 1146-1162.
[4]	祝效华, 刘伟吉. 旋冲钻井技术的破岩及提速机理[J]. 石油学报, 2018, 39(2): 216-222.
[5]	李武广, 钟兵, 杨洪志, 杨学锋, 胡志明, 陈满. 页岩储层基质气体扩散能力评价新方法[J]. 石油学报, 2016, 37(1): 88-96.
[6]	况雨春朱志镨蒋海军伍开松王　勤 . 单粒子冲击破岩实验与数值模拟[J]. 石油学报, 2012, 33(6): 1059-1063.
[7]	李鹏华李兆敏赵金省李宾飞李鹏春. 多段塞平行聚能提高聚合物驱后采收率实验研究[J]. 石油学报, 2010, 31(1): 110-113.
[8]	刘合, 肖丹凤. 新型低损害植物胶压裂液及其在低渗透储层中的应用[J]. 石油学报, 2008, 29(6): 880-884.
[9]	刘永贵, 王洪英. 徐深气田气体钻井破岩机理的初步研究[J]. 石油学报, 2008, 29(5): 773-776.
[10]	林波, 蒲万芬, 赵金洲, 刁素, 宋丹, 张晶, 周明. 利用就地CO₂技术提高原油采收率[J]. 石油学报, 2007, 28(2): 98-101.
[11]	兰玉波, 杨清彦, 李斌会. 聚合物驱波及系数和驱油效率实验研究[J]. 石油学报, 2006, 27(1): 64-68.
[12]	梁金国, 张克舫, 沈惠坊 . 焦化防砂室内实验研究[J]. 石油学报, 1998, 19(2): 132-134.